similar to: ISDN channels not properly released after call

1. If the other end picks up the phone the conversation is successful and when the conversation ends, the channel is properly released: -- CAPI/ISDN1#02/2104988888-0 answered SIP/1000-081d91b0 == ISDN1#02: CAPI Hangingup for PLCI=0x101 in state 2 == Spawn extension (internal, 2104988888, 1) exited non-zero on 'SIP/1000-081d91b0' > ISDN1#02: CAPI INFO 0x3490: Normal call

Dear asterisk users! I want to control a hardware pbx with asterisk. What I need to do this is being able to press "hold" which can be done with capicommand(hold) and then send digits on a bri card which connects to my asterisk computer. So far I use Dial(CAPI/ISDN1/27:<<digits>>/bo,15) to do this. Are there better ways? Note that these are not dtmf, I'm afraid. I use

I have a problem receving calls via the ISDN line, using the followin components Asterisk 1.0.9 with asterisk@home chan_capi-cm-0.6 AVM Fritz card datalink protocol = point to multimode I can make calls out with no problems so the issue is only incoming calls. When I make the call from an external line to the ISDN line connected to asterisk, I get a busy signal after about 5 seconds. I have

Hi, I like to forward an incoming call on an ISDN line to my mobile phone. Since ISDN offers two channels, I thought that this should work, but Asterisk tells me, that there is no channel available. There is no one else using this line, so guess I made a mistake in the configuration or it might not work for another reason. Here's the CLI output , the capi.conf and extensions.conf. 83086921 is

Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over ISDN/Capi but I don't succeed. My `capi.conf' is like show in many tutorial on the web. In `extensions.conf' I just added the following lines: [capi-in] exten =>

Hi! I am playing around with Asterisk and have a problem :-) (Asterisk-version: 1.2.4, chan_capi-cm-version: 0.6.4) I have a sip-phone at my desk and an ISDN-phone (independent of the Asterisk-server) in my living room, when I'm not at my desk, the sip-phone is switched off. I would like to be able to accept calls at both phones (when available) and have Voicemail kick in if I don't

Hi, I have an asterisk with a DIVA Server V-BRI-2 card, connected to a Siemens PABX. From a SIP phone, I can call other internal SIP phones, external numbers (to PSTN), but I can't call internal phones connected to the internal phone network. When I call 107, which is an internal phone, heres the logs from asterisk: -- Executing Dial("SIP/Greg-081f5a10",

[Something seems to have went wrong with my previous posting. It appears on the archive page in another thread. I did not receive anything myself. So I may give it another try:] Hi, the first thing I did with Asterisk is listening to `demo-congrats' by Xlite on the same machine. This works perfectly. The config files are those shipped with the package. Now I want to listen to it over

I seem to be having a problem with B3 on my ISDN line, as you can see from the dial string I am having to have asterisk generate ringing else there is no progress indication. -- Executing Dial("SIP/0014A8ACCB83-fd9f", "CAPI/g1/142392203000/ b|40|r") in new stack -- Called g1/142392203000/b -- CAPI/ISDN1/142392203000-0 is proceeding passing it to SIP/

Hello, I have a noticed strange behavior in Asterisk 1.6.18.2 with ReceiveFax Digium FAX Driver: 1.6.2.0_1.3.0 (optimized for i686_32). I use a context [capi-in] for icoming ISDN calls: ====== [capi-in] ; Faxe fuer Ruben exten => 12345,1,Macro(faxin,ruben.roegels at jumping-frog.org,${EXTEN}) ====== My macro for the fax receiving looks like that: ====== [macro-faxin] ; Faxe ; ARG1 =

-- Executing [2104988888 at internal:1] Dial("SIP/1000-081d91a0", "CAPI/ISDN1/2104988888") in new stack -- didn't find capi device for interface 'ISDN1' [Jan 12 16:20:16] WARNING[3359]: app_dial.c:1191 dial_exec_full: Unable to create channel of type 'CAPI' (cause 44 - Requested channel not available) == Everyone is busy/congested at this time

I've having a big problem after having upgraded to 1.2.4 and chan_capi-cm 0.6.4 When making outgoing calls I don't seem to have any control over the CLI that is presented to the called party -- it can be any one of the MSNs allocated to the line, allocated on what seems to be a random basis. This is on a BT Business Highway line (which is essentially an ISDN2e line with two built-in

Hello everyone, I have Asterisk SVN-trunk-r7498 installed on a server (celeron 2.4 Ghz, 256MB) with a TDM40b a TDM04b and an avm fritz!card pci. I experience a problem with voicemail: my messages are good unless the incoming call comes from isdn, which means via the avm fritz!card. In this case (and in this case only) the message is disjointed and I can hear at most 1 second out of a 1 minute

Hi everybody, I have a problem which I cannot eliminate on my own. Has anybody any idea for the following: I am using the asterisk-version from Debian-Testing (1.2.13) with the latest chan_capi (also tried an older version). When using the Capi-Channel, everything works fine except from the sound it sounds extremely choppy and is unusable :-( When e.g. capisuite is used for fax, everything

Hello Armin, hello List I'm trying to get chan_capi working with asterisk from debian stable (asterisk 1.0.7, the debian version number is 1:1.0.7.dfsg.1-2). I managed to get it compiled by providing my own version of ast_copy_string. This is an Austrian PTP line. I can do outgoing calls fine (no comprehensive tests yet). For incoming calls, I'm getting "No answer" on the

I'm not sure that this problem is strictly related to zaphfc, but this is what happens: my asterisk (build on bri-stuff-0.1.0-RC2k) handles a single PCI HFC-S based card. I own a Cisco 7940 Sip phone (fw 7.1) and a pc running X-Lite. Zaptel.conf and zapata.conf are taken directly from zaphfc samples. Extension.conf contains the following lines: [from-ISDN1] exten=>s,1,Wait(1)

Hi all, I've finally taken the plunge and had isdn installed. It's a BRI from Telewest in the UK. I'm told by the provider that it's in point to multipoint mode with 6 digit presentation. I'm using an AVM fritz (bt speedway) with the fcpci-suse9.1-3.11-02 driver. Chan_capi seems to be installed fine. I can receive incoming calls. However, I can't call out. When ever i

Hi, after I fixed my problem with the playback() application, I now have the next strange one. When I dial the number of our client, located in another town, I get a connection to the asterisk server, I can talk to my client or listen to his mailbox. If some in the town of this client calls him, he gets the ISDN error "service not available". Out office is connected to he office

O.K. thanks a lot, Felix and Peer Oliver. But somehow asterisk keeps telling me while startup: [chan_capi.so] => (Common ISDN API for Asterisk) Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr1 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr2 Jan 24 14:30:47 NOTICE[9796]: chan_capi.c:3271 load_module: Unused contr3 Jan 24 14:30:47

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Ahoy I'm trying to setup Asterisk on debian etch (with the debian packages) with a "Fritz!Card PCI" ISDN card and chan_capi. Everything seems to be configured the right way (excerpts below), Asterisk seems to see the ISDN-card but if i try to place a test-call from the outside i don't see anything on the asterisk-console (set debug