similar to: MFC/R2 Signaling configuration

---------- Forwarded message ---------- From: Brian Hutchinson <b.hutchman at gmail.com> Date: Fri, 11 Jan 2008 12:22:09 -0500 Subject: Trying to build MFC/R2 Hi Moy, I downloaded your astunical-1.4.16 and have been studying it. I have a machine running the latest download of asterisk-1.4-17 and was trying to figure out how to build MFC/R2 support into it. I merged your unicall specific

Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of

I don?t know if the last message was with content. So, I sent again. I have installed a Digium card TE210P and unicall for use MFC/R2. I think that it?s all right but I can?t make and receive calls. I?m using asterisk 2.1 with the patch made by Jos? P. Leit?o and the follow libs: libsupertone-0.0.2 libunicall-0.0.3 libmfcr2-0.0.3 zaptel 2.1 My number is 34318300. The Telco send me only 8300.

Hello there! I've problem with setting up unicall / mfcR2. can't find proper notation for channel, trying unicall/1, unicall/1/1001, unicall/g1, unicall/g1/1000 and still having no luck. klaudia*CLI> !cp call /var/spool/asterisk/outgoing -- Attempting call on Unicall/1001 for application Dial(363) (Retry 1) Mar 25 09:29:34 NOTICE[19920]: channel.c:2429 __ast_request_and_dial:

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and

Hi all, Anyone have an idea which version of spandsp, libunicall, libmfcr2, libsupertone, app_rxfax/app_txfax and chan_unicall I should use for the latest asterisk 1.2? Would that be the ones listed below? http://www.soft-switch.org/downloads/spandsp/spandsp-0.0.4pre4.tgz http://www.soft-switch.org/downloads/snapshots/spandsp/test-apps-asterisk-1.2/

Hi all, I still haven't seen my first post (cry for help) so I'm not sure if these are going through or not ... I've played with the box all day today ... I got it to quit seg faulting finally by playing with the config files. Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP) Here is my zaptel.conf: (I know the device connected to spans 1-3 are providing

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but

Dear Steve and *.* e1r2 developers and users; my first question is: what is the version of linux you use to make asterisk run with the new libunicall? and what is the version of asterisk? my problem is : with version Fedora, C3 I have compile and run libunicall without problem, the testcall.c run also perfectly. and askterisk run without problem on the localm network. I patch asterisk in

Dears, After having set up the board Digium TE420 to receive 3 E1s, I can receive calls without difficulties. As you can see in the log below: -- Executing [5908 at from-pstn:1] NoOp("UniCall/14-1", "Catch-All DID Match - Found 5908 - You probably want a DID for this.") in new stack -- Executing [5908 at from-pstn:2] Goto("UniCall/14-1",

Hi all, I have begun the release of my MFC/R2 protocol software. At http://www.opencall.org/installing-mfcr2.html there are instructions for installing what I have released so far. This is the MFC/R2 protocol software, and a test program. The software to interface Asterisk to the MFC/R2 code will be released shortly. It used to work, but it hasn't been touched for a while, and Asterisk

Hello, i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package: libpri-1.4.2 asterisk-1.4.9 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.4.4 i'm using a E1 pci card with R2 but they not work, when I start the asterisk its generate this log: [May 12 08:53:24] WARNING[30814] channel.c: No channel type

Hi all, I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled, and a Sangoma A101, and when I make a call I get this: Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception: Exception on 19, channel 1 Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101 [1/ 40/Seize /Idle ] Jan 8 13:04:06 WARNING[12252]:

Hello All, we have Asterisk 1.4.9, Unicall 1.4.9-0.1, and Zaptel 1.4.5.1. If we were to update or recompile Asterisk, would we need to do anything with Unicall or Zaptel? Thanks in advance -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080201/b80fa496/attachment.htm

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hi all I have MFCR2 successfully installed but seems to get warnings a s seen below when I start asterisk. Am running on Redhat 9. Asterisk Ready. *CLI> Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 far_unblocking_expired Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 local_unblocking_expired Dec 20 08:40:38

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Dial(UniCall/g1|300|) Where is the number you want to reach? I'd expect to see Dial(Unicall/g1/1234567890|300) To reach number 1234567890 - Mois=E9s Silva On Jan 30, 2008 1:21 PM, Roger C. Beraldi Martins <rogerberaldi at gmail.com> wrote: > Dears, > > After weeks trying to contact support of my telecom about 'Seize Ack' > because that is not returned, was a