similar to: :POSSIBLE SPAM: conferencing help

HI, my problem is with internal sounds of asterisk. for example when calling voicemail, no system recordings are being played back. However, when running asterisk in a debug mode, i see the call coming through to the system and the system playing back the wav files promptly. However, no sound comes through. I have verified that the sounds are in the correct location and that asterisk:asterisk has

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as

Sorry but i can't register in the freepbx forum, so this is my solutons for resolve my trouble. HI, my problem is with internal sounds of asterisk. for example when calling voicemail, no system recordings are being played back. However, when running asterisk in a debug mode, i see the call coming through to the system and the system playing back the wav files promptly. However, no sound

Hi, I am using asterisknow 1.5.0 and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. I think the same problem listed here: https://issues.asterisk.org/view.php?id=6683 There is one patch on this link but i don't know how to apply patch on asterisknow.

Hello, I am trying to alter the outbound callerID for extensions within a context I have created. I wrote the following: exten => _9.,2,ExecIf($[$["${REALCALLERIDNUM}" = "360"] | $["$ {REALCALLERIDNUM}" = "670"]]|Set|CALLERID(num)=581560) exten => _9.,3,ExecIf($[$["${REALCALLERIDNUM}" = "361"] | $["$

Dear All, I have an asterisk server version 1.2.12.1 along with trixbox and I am having this nasty problem, I have a TE200P and have an E1 pri attached to it and zttool says it's OK, I have configured the whole 31 channels into one group as follow: Zapata-auto.conf: callerid=asreceived signalling=pri_cpe switchtype=euroisdn context=from-zaptel group=0 channel=>1-15,17-31

Hello everybody, and first of all sorry for my poor English. I'm having trouble with Quadbri installed on Asterisk 1.2.17-BRIstuffed-0.3.0-PRE-1y-e. Everything is working fine, except calling to switched off or "out of coverage" cell phones. In this case I have to wait 40 seconds until Asterisk tell me that "all circuits are busy now" instead of receive cell phone

i have posted this question couple of times and never really got any hits i wasn't able to provide any debug info Connected to Asterisk 1.6.0.21 currently running on phoneserver (pid = 3309) Verbosity is at least 4 == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 == Using SIP VRTP TOS bits 136 == Using SIP VRTP CoS mark 6 == Extension Changed 117[ext-local] new

I have call center PCs that switch between an IBEAM SIP softphone and a NEBU IAX softphone (for reasons that aren't germane here). The SIP softphones work fine, but the IAX softphones get a fast busy unless I give them an IAX trunk to use, instead of the PRI trunks that all the other phones are using. I am using Asterisk 1.2.3. svn rev 47264. I've appended a sample call trace. The

Hi, I use: Trixbox-2.2.4 FreePBX-2.3.1.0 Asterisk-1.2.17 BRIstuffed-0.3.0-PRE-1y-e Zaptel-1.2.19 ..with two ISDN cards, often but occasionally the dial out failed but is possible to receive external call. My zapata.conf conf is: [trunkgroups] [channels] language=it context=from-pstn signalling=bri_cpe_ptmp rxwink=300 pridialplan=unknown prilocaldialplan=local switchtype=euroisdn

I am using asterisk version 1.2.6 with Zaptel version 1.2.5. I have a POTs line coming into a Digium TDM01B. It appears to not be getting CID at all. If I hook up a POTS phone to the line CID comes through fine. Inbound and outbound calls work fine but there is just no CID on inbound for this channel.The incoming route for the channel is Zaptel Channel 0. No DID or CID settings applied. My IP

I just had a user report that they called out to someone on a cell phone this morning, and after a short conversation, the call was dropped/lost. The person on the cell phone says that this is very rare, and would not suspect the dropped/lost call to be on their side. I have looked at the asterisk/full log as thoroughly as I can, and have pasted the lines which seem relevant to that call below.

hi,all when i send a call to other server use SIP trunk, i got this below, <--- SIP read from 222.46.18.52:5060 ---> SIP/2.0 403 Forbidden what's rong with is? > Asterisk 1.4.21.2, Copyright (C) 1999 - 2008 Digium, Inc. and others. > Created by Mark Spencer <markster at digium.com> > Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for

Hello, Sometimes the call gets answered for 1 second, but actually the phone has not rang, it?s just the CDR, and asterisk hangup automatically, I cought the log of 1 call like this, I hope you can help me with this. My setup is : <vendor> ----SIP--? <Asterisk> ?----IAX2---? <Asterisk with Dhadi channels> Here: -- Executing [966505103150 at from-internal:1]

Hi, i got Ubuntu 6.06 installed and theres a problem with asterisk. I've sucessfully installed it with the command: #apt-get install asterisk Then after installing FreePBX i get this error when restarting asterisk: root@hernandezz-laptop:/home/hernandezz# asterisk -rvvvvvvvvvv Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?) After looking at the logs i

Hello. I am running Asterisk v1.6 on Ubuntu 10.10 with FreePBX v2.8. When I call the voicemail for any of my extensions, the call just dies. On a softphone, I get no sound whatsoever; it just hangs up after a couple of seconds. On my handset attached to my SPA-3102, it get a sound like when you leave an analogue phone off the hook. I have three extensions setup and they all do the same thing.

I'm using FreePBX 2.5.2.2 with Asterisk 1.6.1.4. If I make a call and then decide to blind transfer them using ## my side of the call is not hung up. Instead it sends me to voicemail. If somebody calls me and then I blind transfer them with ## I am hung up on as expected. I called from 8678 to 28688. I then transferred the call to 8532. Asterisk acts like it wants to hang up, but then

Hello everyone! I've had this problem for a while and cant figure it out. When an outside caller calls an extension on my asterisk system, they do not hear any sort of ringing. Inside extensions calling other extensions do hear ringing. We have 3 other asterisk systems that are configured the same way, but do not have this problem. We think it has something to do with asterisk 1.6. The other

hello list i have an issue related to outbound calls i can contact all the number except on number given by our provider in trunk the issue just when i configure my trunk in our server but when i configure the trunk directly in x-lite i can contact this number without issue below the cli == Using SIP RTP TOS bits 184 == Using SIP RTP CoS mark 5 -- Executing [0149xxxxxx at

i have a prablom here, i want to send a call from A to B use sip trunk , the call can sended B,but not work to PSTN. the message from B server. help pls,what's rong? > > <--- SIP read from 192.168.0.176:5060 ---> > INVITE sip:15921256331 at 192.168.0.151 <sip%3A15921256331 at 192.168.0.151>SIP/2.0 > Via: SIP/2.0/UDP 192.168.0.176:5060;branch=z9hG4bK51a51b96;rport