similar to: HFC-S zap channels always busy

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hi list, After upgrading from Asterisk v1.2 to v1.4.14, all kinds Zaptel error messages related to my HFC-S PCI card disappeared, but now I can't access the card's resources because it always seems to be busy. Any idea why? Thanks, Jaap PS -- Below is some info regarding my configuration. =========================== Zaptel version: 1.4.7 (incl. firmware and modules). OS: Debian

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

Hi list! I'm totally fed up with bristuff (or it's instability with a simple HFC-S card), 2 out of 3 times when people try to call they get the information tone that the number is not connected. I would like to try vzaphfc and I am looking for information on it. >From previous posts I found that the only place where the sources seem to be maintained and available is at the debian

Hi all, On an Asterisk/Zaptel 1.4 system, one way to gather diagnostic info is: ~# cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A Zaptel Driver card 0 [TE]" (MASTER) AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) Span 2: ZTHFC2 "HFC-S PCI A Zaptel Driver card 1 [TE]" AMI/CCS 4 ZTHFC2/0/1 Clear 5 ZTHFC2/0/2

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Hello, I tried to connect my Siemens ISDN 4170 cordless small PBX to the asterisk with an Acer HFC isdn card but I have not seen any success. The asterisk can see the card but no success to receive or dial a call. The Siemens 4170 gives fault in all the handsets with trying to dial and does not receives anything. I have linux kernel 2.4.29, asterisk CVS-v1-0-03/12/05-17, zaphfc

Hi all, In our asterisk box we have a Fritz card and an HFC card. So far I've had the Fritz card working well, but its time to connect the HFC card up to the ISDN line and get it working. I've followed the instructions on voip-info.org here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install and here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install But when it comes to

so here it is, the problem that's been nagging me for the past 2 days: connected a box to my telco's NTBA <-> zap/asterisk. which works: box:/etc/asterisk# cat /proc/zaptel/1 Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" HDB3/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In

Hi, Can anyone please point me in a direction as to how to set up these 2 pci cards with AAH 1.1? I have (am still) googling left, right & center - but haven't found a definitive guide yet. The centos based setup lacks any of the tools I know (insmod, modprobe ....) so it is time consuming just to even dig around the AAH box. There are no zaptel.conf files ....and on it goes. A

Hello, I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode to dial-in and out with ISDN. The problem is I can not get the card to dial out with a Zap channel. Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3 and RC2k). I tried all combination of "immediate", "overlapdial", "pridialplan". I earlier also managed to dial out

Hi!I've installed Asterisk@home and I have a ISDN card,(Cologne Chip Design GmbH ISDN network controller [HFC-PCI](rev 0.2) This is how I installed bristuff: how to install hfc card after unload asterisk and amportal whit amportal stop type "setup" unselect zaptel in system service... and set the lan --->reboot<--- cd /usr/src wget

Hi all, Previously, I had the PrivacyManager working for me exactly as would be expected, but after upgrading the OS to Debian lenny and Asterisk to v1.4.21.2 that's no longer the case. Anonymous callers are still confronted with the PrivacyManager, but now no matter what I set the minlength value to, e.g.: exten => jaap,n,PrivacyManager(1,1) ... (I'm not using a

Hi, Has anyone information about BRI hardware supported by 1.6 libpri ? In another thread, I was told a basic BRI card with HFC chipset (Bewan Gazel 128) was supported but I would delighted to lear about other harwarde (and specifically about Digium B410P). Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello everybody, I'm having little trouble (well, pretty big trouble) with HFC-S card and Asterisk. My idea is to do VoIP/IAX link between two HW PBXen using two Asterisk PC boxen with ISDN cards in them. AFAIK HFC-S cards must be in NT mode for this installation, they must behave like state line for those HW PBXen. (if wrong, please correct me). Diagram follows: