similar to: Polycom VLAN

Hi, all. I see that the Polycom SoundPoint IP 330 supports VLAN... but I don't quite see how that works. Do you point a non-VLAN'd segment at it (akin to when you uplink a VLAN_enabled switch), and have the phone implement the VLAN? Or...? *puzzled* Thanks much, -Ken

Andrew and Dennis are spot on. Their conclusions about your server being connected to an access port and not a trunk port would be my conclusion as well. On Sat, Jan 24, 2015 at 9:11 AM, Dennis Jacobfeuerborn < dennisml at conversis.de> wrote: > Hi Boris, > what I'd like to know is the actual VLAN configuration of the switch > port (link-type and tagged and untagged VLANs).

Do you need the whole configuration? On the switch end, we have the relevant VLAN (VLAN 48) with the assigned IP address of 192.168.48.101 and the range of ports (Gi1/0/1 - Gi1/0/8) assigned to that VLAN. Seems - and acts - like a legitimate setup and works fine, except for this particular instance. Thanks. Boris. On Fri, Jan 23, 2015 at 8:54 PM, Dennis Jacobfeuerborn < dennisml at

Hi, The attached patches enables the bridge to filter and forward packets according to their IEEE 802.1q headers. The goals behind this change include : - Enable running STP on 802.1q tagged networks. STP packets must be untagged. It isn't obvious how else to enable STP with the current bridge and vlan code. - Add native support for an untagged vlan. Currently an untagged vlan can

Thank you everyone. OK, the mystery deepens, I guess. The machine does need to support several VLAN's, it is currently on a trunkport (8021q encapsulated), it made it into the ARP table - which I specifically tested for by physically unplugging the table, clearing the ARP table and plugging it back in. The ARP table currently looks like this: hq#show arp Protocol Address Age (min)

I''m playing around with VLAN''s and I have a VLAN capable (layer 2) smart switch. I see a steady stream of martians in the logfile if I have the routefilter option set on the loc zone interfaces in /etc/shorewall/interfaces. I have two interfaces in the loc zone, eth1 and vlan2 respectively. vlan2 is an 802.1q trunk going towards the switch. Is this the expected behavior in

On 25 January 2015 at 15:12, Boris Epstein <borepstein at gmail.com> wrote: > OK... but why does it need to be a trunk port? > Because a trunk port will "trunk" the vlan. A VLAN is basically a 4 byte "tag" that gets injected into the packet header when the packet enters the VLAN network. When we trunk a VLAN we say to the switch "pass packets on VLAN x but

Hi All, For my issue, first thanks to ALL, I have some idea of it. Also Thank Peter for his kind remind, I would become one good guy in this list. Most mentioned MTU, but how I assure that the problem is just MTU, how I debug it? Here is my bridge configuration: Internet | | Gateway | | eth0 Ethernet Bridge | eth1 | H u b ( one normal hub

Hello to everybody, Sorry if my english isn?t very good. I need pass 802.1q through a VPN between two offices. I have mounted a WRT54GL, with OpenWRT firmware, conected to a switch trunk port in both offices. In the switch of the first office I have created five tagged VLANs and I need pass these VLAN to the second offices where it has created it too. Can I do this with Tinc in HUB/Switch

Can an asterisk box equipped with a Digium T1 card handle Integrated T1 circuits? I have a T1 with 768k data and the remaining channels voice, can the asterisk box do the Data routing + Voice processing? It's only going to support 4-5 users(the voice channels won't all be active obviously). ________________________________ This e-mail, facsimile, or letter and any files or attachments

Hello, I have been tearing my hair out on this issue for 2 days, any help would be appreciated. We have a normal network and a Cisco SGE2010P switch - a 48 port PoE switch There are two VLANs, 1(data) & 50(VoIP). When Polycoms are connected to the switch with VLAN 50 hard coded in the config they grab a DHCP address from VLAN 1, the PVID for the switch port. The ports have membership in

Has anyone been succesful pushing a VLAN setting to a Polycom phone via DHCP? I can push the boot server via option 66 but that is about it. I have set it for 'fixed' and tried many different option numbers with a couple differnet DHCP servers. SIP firmware 1.3.4 or 1.4.1 doesn't make a difference. Aloha, Matt

Hello all, I have a machine running Centos 6.6 connected to a port on a Cisco Catalyst 3750 series switch. That port is part of VLAN 48. I have VLAN 48 on the CentOS machine too. The IP network on VLAN 48 is 192.168.48.0/255.255.255.0. The address on the CentOS side is 192.168.48.101, the address on the Linux end ought to be 192.168.48.100. When I only bring up eth0.48 VLAN device with the

<I apologize if this arrives twice... I sent it first from an non-subscribed address, don't know if that'll get to the list or not --JJ> Hi folks, I have an implementation question regarding bridging on a linux box between a catalyst trunk port and a cisco 26something w/802.1q subinterfaces. So right now, there's no vlan trunking going on on the link my bridging firewall sits

Hi -- The environment we have is as follows, Domain controller: samba 3.0.14a running Solaris 9/X86 Authentication: openldap 2.2.14 Clients: Windows XP with SP2 The issue I met: If both clients and Samba server are on the same physical switch (also same subnet), the clients can join the domain and users can log into their domain accounts without any problem. However, if the clients

So has anyone had any experience working with the polycom 501 or 301 and vlans? We run dell managed switches here, so we don't have the luxury of running CDP to force the VOIP vlan. I haven't been able to get the polycom phones to talk on a manually set vlan. I have some junky sipura phones that work fine-(get dhcp, register to asterisk etc) when i manually set them to vlan4. Any advice

Hello, I use a script network-multi vlan and network-bridge-vlan for multiple VLANs in domu. Several domu uses the bridge vlanbr30. Need to dom0 as was in this vlan''e. How? I tried to put a bridge interface ip, but with him until the rest domu in vlanbr30 not get through. How to understand the need to create a virtual interface (vifx.y) and add it to the bridge vlanbr30. How?

Hello. I''m trying to use vlan in domU, but have something strange: I created bridge on eth0. This interface was configured as trunk with vlan 300, 301. I use this bridge in my domU, and I can see tagged packets when run tcpdump in domU. Also I created interface on domU to work with vlan 300. On this interface I see untagged packets in vlan300. And everything looks fine. But when

Hello You must add first: vlan (tagged) to eth2 eth2 interface is not tagged by default and not know vlan-s . It is like a cisco if you have 24 ports in cisco by default all ports are in vlan1. if you want to do trunk (with vlans) you myst add (vlans) to this ports (tagged or untagged) So you can compare that all interfaces in linux by default are in one vlan(but not tagged). (only for

Does anyone have any tools to process CDR-CSV files into reports? I don't have anything specific in mind, I'd just like some reporting examples so I don't have to reinvent the wheel. ________________________________ This e-mail, facsimile, or letter and any files or attachments transmitted with it contains information that is confidential and privileged. This information is intended