similar to: Samsung iDCS 500R2 <PRI> Asterisk 1.4.*

What is the recommend Digium Card for a PRI in NA ? I want to interface a Asterisk Server to a Samsung iDCS System, and have available T1 w/DNIS, or a PRI w/DID, the asterisk server would need to appear as a "Telco" provided Circuit. Slot Availability. Four PCI-Express Slots x8 (1 full-length/1 half-length/2 low-profile).

Any Recommendations on a "Good" Wireless Voip Keyset that works well with Asterisk? I would prefer one that is IAX2 as it works better behind a Nat'd Firewall.. But I am reaching out to you guys as you all would know what would work the best :-) ________________________________________________________________ Sent via the WebMail system at kotbh.net

Hi, I've now set up Asterisk to interface with our current Samsung iDCS 100 PBX via an 8SLI analogue extension card in the Samsung and an Openvox A400P04 4-FXO card in the Asterisk box. It all works in that I can place calls in both directions from the office Samsung extensions and Asterisk SIP extensions. The only tricky bit was getting the FXO to detect hang-up from the Samsung correctly -

I am trying to determine what would need to be done/modified to enable the following: I have a SIP extension come into my asterisk box, and I then need it to call "6-10" remote Sip Stations that are set to Auto-Answer... (note, my remote sip stations are actually cisco h323 devices, I can call them fine from any softphone, or other device, and have full-duplex audio, however, i need to

What are people's thoughts on asterisk 1.2.26? Any show stopping bugs? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080117/57d1002d/attachment.htm

How well does the Grandstream GXW-4104 or (8) work w/Asterisk? I would use a Cisco Switch w/FXO Ports but that would be a little "Pricy" I Can't use a Digium FXO Card, as the asterisk Server is offsite. Thanks, William Stillwell KI4SWY ________________________________________________________________ Sent via the WebMail system at kotbh.net

Im sure this has been thrown around this list 1,000 times, and Im sure its been around the net too.. But I have done everything, and cannot seem to get inward calls to be processed on my asterisk box.. First, Let me tell you what works: 1) Softphones (ZoIPer using IAX2 Protocol) Can make calls behind a Natted Firewall to the FXS Port, and it rings, and calls work full duplex. 2) Soyo IP Phone

I have a test setup like this: host ======= *puppet-idc*: Ubuntu 12.04 running ActiveMQ, Mcollective, puppet agent and server *puppet-node1*: Ubuntu 12.04 running MCollective and puppet agent *puppet-node2*: Ubuntu 12.04 running MCollective and puppet agent *puppet-node3*: CentOS 6.3 running MCollective and puppet agent I installed the *mcollective-plugins-puppetd plugin* on all *3 Ubuntu

Hi I have small query, all our server are centos based 5 and 5.2 . We are looking ofr a tool to that measure packet loss. we have servers in two IDC's bothin the US and we are trying to download a 2gb file from the internet. Some server are able to download the file at a higher b/w rate in one IDC ...while servers at he the other IDC download the same file at a lowe b/w rate . Is ther any

Can some one give me a tip on how do I integrate two asterisks Thanks Felippe Kilian Martins NPD-UFSC ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program.

Hi pros, Newbie to asterisk, need some help. My existing senerio is we have 6 analog quintums and 1 digital H323, and our gatekeeper is gnugk openh323 located in US. Our business is Call Center and our method of dial is using prefix and gateway IP provided my Carrier. I also brought two AudioCodes MP108 8 FXS gateways, as our gateway runs on h323 my friend suggested to go for Asterisk. If

Hi,Olaf, I have some questions about event channel in Xenpaging to ask you. 1) In xenpaging it uses Inter-Domainain Commnication (IDC) between dom0 and domU to build bidirectional connection,but I found there is only an event channel notification from xen to dom0 when page faults happens.It seems that xenpaging_resume_page()->xc_evtchn_notify() doesn''t make any difference.So why

Hi, One of my servers in a IDC in another country mysteriously went down this morning, and when I contacted the IDC, I was told that XEN doesn''t boot up, as follows: [QUOTE] This is error message on the screen " Error 19: Linux Kernel must be loaded before initrd" Server is currently up with 2nd kernel. Please check the grub.conf. [/QUOTE] Looking at grub.conf, I see the

my server is on centos 5.5,it is just a new reinstall system i build a php depend on server and used nginx,php,mysql ssh is default 22 port The system perfomance good a few time.but it is always happen a problem only need hardware reboot to solve.the server is on idc.so i can not see the local screen information. the appearance is: 1.it can not use ssh to connect,it show server is down or

Hi, I compiled rsync on an HPUX 11i box, and got lots of errors about redefining sendfile() and sendpath(). The compilation succeeded, but the binary failed. I then took a binary I had compiled on an HP11.00 box, and it worked fine. I tried this with both gcc & the HP ansic compilers. The same results. I am attaching a full transcript of the configure & compilation session. The ld

hi ,all When realizing a resources ,can use this syntax like this ? File <<| tag == $idc | >> I had try it ,but can''t work. and not get error from the puppetmaster. -- Huang Mingyou

Hi I have a data.frame with 2 columns. The first column is an ID column. The other columns are description of the ids. There is more than one description for each Id. Want I want to get as a value is a data.frame where each row corresponds to one ID and has as many columns as different descriptions. I have used a very convoluted step, but I'm very convinced there is an easier way to do

Hi to all, nearly one year ago someone ask about the kea-DHCP support for Samba. In the Samba wiki I still can only find the idc-dhcp stuff. @Rowland will you (and can you) replace or add the setup of kea to the wiki? Would be nice :-) Stefan

Hi I have recently installed CentOS 7.1 on my laptop. Earlier i was using Ubuntu 14.04. I have managed to successfully install all the apps that i was using in ubuntu in CentOS 7.1 except for the app named as: HomeBank http://homebank.free.fr/ Here is the information about my system: [jatin at localhost ~]$ cat /etc/*release CentOS Linux release 7.1.1503 (Core) NAME="CentOS Linux"

When i try to join win2k to samba domain using root as Domain admin users, there's always error that said "The account used is a computer account. Use your global user or local user account to access this server". actualy what user should i put in when win2k asking for user and password to join the samba. i'm using samba-2.2.3 --------------------- Yang Mudah dan Menghibur