similar to: OpenVox B800P and asterisk 1.4/ mISDN-1_1_7

Hello, I have a strange problem with misdn.conf When I run asterisk, I have this message : Apr 3 23:00:25 WARNING[6824]: misdn_config.c:579 _build_general_config: misdn.conf: "use_callingpres=yes" (section: general) invalid or out of range. Please edit your misdn.conf and then do a "misdn reload". Apr 3 23:00:25 WARNING[6824]: misdn_config.c:579 _build_general_config:

I would like to know if the following misdn warnings are relevant. Currently, I don't need echotraining. However, I took a quick look at the * source code and l1watcher_timeout seems to be defined (echotraining was not found). Currently I'm setting l1watcher_timeout to 0 which is default (so I suppose that this warning won't affect me). Any comments on this? *CLI> misdn reload

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hello all! I just noticed, that since installing the latest SVN branch (152803), I receive the following error, when loading/reloading the misdn.conf file misdn reload [...] [Nov 3 16:20:37] WARNING[5267]: misdn_config.c:938 _build_general_config: misdn.conf: "misdn_init=/etc/misdn-init.conf" (section: general) invalid or out of range. Please edit your misdn.conf and then do a

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hi, I have switched a while back from chan_capi to chan_misdn. When the number is dialed and the phone is then picked up everything works just fine. Some users however FIRST pick up the phone and then start to dial... I did not get this to work with misdn. When two digits have been dialed, asterisk sees the extension as complete and does not wait for further digits. I am using an midsn NT

Hi i need to install a server with this hardware: 1 OpenVox B800P 1 OpenVox A800P01 4 OpenVox FXS-100 FXS100 4 OctWare SoftEcho SOFTECHO Do you suggest 1.2 or 1.4 branch? Is now 1.4 stable ? I've tried 1.4 the last year but i've experienced many problems with misdn drivers. Thanks -- /*************/ nik600 https://sourceforge.net/projects/ccmanager

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

Dear Supports, I was attempting to install BRI Card(OpenVox B800P) with wcb4xxp in NT mode .But I can not make it worked! Could you please give me some hints? Thanks in advance! Here are my environments: ------------------------------ CentOS-5.3 Kernel-2.6.18-164.el5 asterisk-1.6.1.6 dahdi-linux-complete-2.3.0+2.3.0 libpri-1.4.10.2 OpenVox-B800P(the first port is spliting into

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files

Hi list, I've installed Asterisk 1.4.0 with newest mISDN 1.0.4 + mISDNuser 1.0.3 on Fedora Core 6. I get many compilation error on mISDN. It wants to include linux/config.h That I fixed by removing the #include line at every occurance. (Don't know if that was a wise move, but it then compiled). mISDNuser and asterisk compiled fine, and asterisk can find and use the ISDN BRI port in

Hi all, I'm fighting with a really strange problem that is really busting me. I have an asterisk 1.4.22 ( from a trixbox 2.6.2 ) and mISDN 1.1.7 3 extension on hardphone and 3 extension in softphone ( zoiper ) What happens is that sometimes the people on the other side of communication hear my voice as metallic and chopped. This happen either on incoming call than on outgoing call. If I

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

I'm having trouble installing Beronet BN4S0 card. I have downloaded instructions from here http://www.beronet.com/download/card_installation_guide.pdf And when I download install-misdn-mqueue[1].tar.gz I untar it and execute "make" and "make install". This is the output that I get. [root@nbirma1 install-misdn-mqueue]# make install make -C app_bundle make[1]: Entering

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Installation fails with a non-explaining error. here's the log: Code: fixme:console:AttachConsole stub ffffffff Starting installer... UI mode : Full GUI. fixme:wuapi:update_installer_get_IsBusy fixme:wuapi:update_installer_get_RebootRequiredBeforeInstallation fixme:ntdll:NtLockFile I/O completion on lock not implemented yet fixme:ntdll:NtLockFile I/O completion on lock not implemented yet

Hello people! I've problems with the installation of Photoshop cs3 or cs4. When i try to install with the setup.exe Photoshop cs3, it give me this: deandreon at deandreon-desktop:~/Scrivania/photoshop2$ wine setup.exe fixme:console:AttachConsole stub ffffffff Begin Adobe Setup UI mode: Full GUI fixme:ntdll:NtLockFile I/O completion on lock not implemented yet

Hi, how you can read in the title, I can't install Photoshop CS4, but here http://appdb.winehq.org/objectManager.php?sClass=version&iId=14318&iTestingId=41796 you can see that Photoshop CS4 works. Why can't I do it? I use Wine 1.1.17 because there is a screenshot where Photoshop is installed under Wine 1.1.17 and run under Wine 1.1.20. This is the outpute when I write wine

I am trying to compile speex.1.1.12 for Symbian OS but I get lots of errors: C:\Programmi\Symbian\7.0s\Series60_v21\Series60Ex\speex-1.1.12\symbian>abld buil d wins udeb make -r -f "\Programmi\Symbian\7.0s\Series60_v21\EPOC32\BUILD\PROGRAMMI\SYMBI AN\7.0S\SERIES60_V21\SERIES60EX\SPEEX- 1.1.12\SYMBIAN\EXPORT.make" EXPORT VERBOSE =-s Nothing to do make -r -f