similar to: Installing/configuring TE120P debian way

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

Hi, all I want to configure a few FXS ports in an Antribank-16 to be able to receive faxes sent throught a PRI: E1 ==>Zap * ==>FXS * ==>Fax machine My asterisk box has a Digium TE120P (for the PRI). Versions are *=> 1.4.17 | Zaptel=>1.4.8 | libpri=>1.4.5 The Astribank is not configured yet, because I am a little bit confused about how to do it. Let's say I configure

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

Hi all I have a small problem here. I asked this question on another asterisk mailing list, but nobody seemed to be able to help me there. We are running * Asterisk 1.4.17 * Libpri 1.4.3 * Zaptel 1.4.8 on a 1.6 dual core, 2GB ram and a digium TDM800P wildcard, hardware echo cancelation and a quad FXO card. We have 4 analog lines, one of which is a Cellphone line for least cost

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all I am working in a new set up with Grandstream GXP-2000 handsets. I like those phone, but they lack a feature I need: the phone cannot be locked by the user. What I actually want is a user to be able to avoid someone else making calls from his phone without giving him access to SIP configuration access to the phone. i.e. let say I want user

Hi @ all, i set a server to a costumer of mine with a TE207P for use with 2 E1 Lines. I set them together into one group in zaptel/zapata.conf The point is now, the customer has a free-volumina of 60k minutes per month, per line. How can i make a kind of load balancing, that both lines will be trafficed the same way ? I read something about DIAL(Zap/r1/.) for using round robin, and

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

I have a brand new TE120P card that I have installed and asterisk is not starting as I am getting the error: ERROR[5054] chan_zap.c: Unknown signalling method 'pri_cpe' It seems it does not matter what I change the vaule for signalling= to, it always returns it as invalid. I have tried the config from my other 2 servers running TE110P cards and the config from AusTechPartniships

Dear all, I have small question in sip.conf I added [service] type=friend ;username= ;secret= qualify=900 host=X.X.X.X dtmfmode = rfc2833 disallow=all ;allow=g729 allow=gsm allow=alaw allow=ulaw and I can proccess incoming call from soft phone only I calling on number that is used in extensions.conf(in example below it is 1) exten => 1,1,Answer; exten => 1,2,Playback(hello-world,skip);

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).

Hi Folks, I have a T100P ordered from Digium in the past. Its working perfectly fine but I now need to more the server to India (out-sourcing) and we will be getting an E1 line there. Does anyone know if T100P was capable (upgradeable) or swappable so that I could use it with the E1 lines instead? Any pointers to driver/firmware update would be highly appreciated. Thanks. R -------------- next

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all I have already a fully operational Asterisk PBX connected only to the IP world. As a necessary step before smashing our current PBX, I need to install and configure an ISDN card able to take an incoming E1 line provided by Eircom. That's the one and only ISDN line we will ever have, so I am planning to get a single port card similar to

Hi, I recently installed a TE120P in my lab with a full voice PRI (23 channels + 1 D channel). Everything is working well except echo cancellation; for the most part this isn't an issue unless one of the users is in a conference. I'm getting the following error when a call is picked up (incoming or outgoing): [Feb 25 12:54:01] WARNING[8661]: chan_zap.c:1437 zt_enable_ec: Unable to

Hi guys, Hope someone can help me with this... I got an Asterisk with TE120P card... using dahdi 2.1.0.4 and asterisk 1.4.24. The problem is the link between the card and the telco... suddenly through the day looses connection... and the people on site just power cycle the PC and the problem got fixed.... for a while.... I've already replace the cable between the card and the telco. Telco

I am aware of how to match a particular caller-id or a caller-id pattern and do something with the call like this: exten => 15554441212/_888NXXXXXX,n,Playback(GoAway) What I am curious about, is the best way to block unknown, private and 000-000-0000 calls. I know I can do this for 000-000-0000 calls: exten => 15554441212/0000000000,n,Playback(GoAway) Is there a better way to catch

http://voip-info.org/tiki-index.php?page=Asterisk+bounty+SIP+simultaneous+registry From the WIKI: Contributions Manager: Daniel Jimenez (cuban) Bounty: $50 USD Date opened: July 10, 2004 Contributors: cuban ($50) Detail Yes, Yes I know you could do all sorts of fun with the dialplan to produce a similar effect, but I still would like to be able to do this. Plus it's easy money :). I

Hello List, We purchased a TE120P card from Digium and it works great. The only problem is that we are still experiencing echo on some calls. I've tried various echo cancellers (right now we are using OSLEC) and still no luck. My question has anyone gone from the TE120P to a Sangoma A101D-X Single Port T1/E1/J1 w/ echo cancellation? Have you noticed a difference? Also I called

Here is the scenario: Asterisk 1.14.13; zaptel 1.4.6; Digium TE120P (same problem with various previous versions; same problem with different TE120P cards). The customer has a partial (10 B-Channel) PRI that when it is busy (eight or more B channels in use), tends to fail as shown below... [Jan 26 23:00:31] ERROR[31893] chan_zap.c: Write to 28 failed: Unknown error 500 [Jan 26 23:00:31]