similar to: dial in group

Hi all, I have a TDM400 with all FXO on it. When I make an outgoing call, I can hear callee but callee claims the volume is too low so that he/she can't hear very clear. Can I adjust to increase the volume in callee side? Is it increase the value of txgain can solve the problem? ango

Hi all, I will a TDM card with FXO modules on it. Below is the dial plan. When someone can 9123456, CLI will show dialing to 123456 and answered. After answered, the call hangup. I would like to know what will cause the case to happen. Anyone can give me some advice to solve it? exten => _9X.,n,Dial(Zap/g0/${EXTEN:1}|${RINGTIMEOUT}) exten => _9X.,n,Hangup zapata.conf

I have a TDM400 in the server. I want to press **1XX to pickup a call. It is ok if I pickup a call dialled from 1XX to 1YY (internal network call). However, it is failed to pick up a call from PSTN thro' TDM400 card. It seems I can't guess the correct context of it. How can I know the context of the call using CLI? The default context of the TDM400 is from-pstn but pickup still

Hi all, Is it possible to install more than 1 asterisk in a single server? If yes, what do I need to set and take care? Rgds, ango

HI, Does asterisk will ignore the setting in files if realtime is applied, say asterisk will ignore all the setting in sip.conf if realtime table sip_buddies is applied? ango

HI, We are experiencing the hum noise when the conversion of 2 parties is established. How can we eliminate that noise? ango

hi all, We have a TDM400 card with 4 wfo modules. now the modules load fine and when i start asterisk with on phone line connected it just starts spewing these messages: -- Starting simple switch on 'Zap/4-1' Jan 13 12:59:47 NOTICE[10831]: chan_zap.c:5367 ss_thread: Got event 2 (Ring/Answered)... Jan 13 12:59:47 NOTICE[10831]: chan_zap.c:5367 ss_thread: Got event 2 (Ring/Answered)...

I have a very strange problem I'm hoping someone has encountered already. I've scoured the internet for an answer to this one. My phone company provides no disconnect supervision. Hence I'm forced to use the busydetect feature. I have a TDM400 with two FXO ports. If I call from an internal extension to a landline and then hangup the landline Asterisk detects the busy signal

Hi all, We have tested both tdm400 and BRI 1 port HFC based with mISDN driver and with both cards we have the same problem... so probably it's due to our misconfiguration, but we couldn't find anything useful on google. With TDM400 we can place and receive calls, but if we receive a call from TDM400 and we reject it from a sip phone , asterisk send the hangup but the line continue to

HI, I have 2 TDM400s plugged in a PC. I failed to use same channels to make a call to PSTN. It shows it can't establish connection after dial command issued. Below is the log. Actually, the call is established as I can hear voice from the called party but the softphone is still showing ringing. It seems the TDM card can't get an answered signal from PSTN. After 15 seconds, the call

Hi all, I have hit a wall configuring a TDM400, I have set these up before without issue but today I just can't seem to figure out what I am doing wrong. On an incoming call the following is produced in the Asterisk console with verbose 4 -- Starting simple switch on 'Zap/2-1' Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring Begin)... Mar 22

I tried adding wwww to my dial string... It appears to not made any differnece. I see by watching show channels that the w's are there in the dial. I have this box connected to bell south down in georgia. I have an identical box connected in indiana. The box in indiana works fine when dialing out. When in GA dialout is getting "you must first dial a 1 to place this call". show

Hi all, I have installed Centos completely. However, the LAN doesn't work. Below is the message after I issue. How can I make it work? 00:19.0 Ethernet controller: Intel Corporation 82567V-2 Gigabit Network Connection Thanks!

Hi, I use realtime and I found that changing accountcode needed to restart asterisk to activate that code and shown in CDR. Does it has a way to update accountcode without restart asterisk? ango

Hi all, I have read many forums and discussion groups talking about fax support in asterisk. Some of them conclude that asterisk doesn't support fax. However, some of them conclude that there is no relationship between fax and asterisk as asterisk will only pass the fax signal to the fax machine. I have tried the fax in asterisk before but failed. Anyone can give me some guideline how to

Dear List, My problem is that the incoming Caller Id is not displayed on the local analog phones (connected to a TDM400 card). I receive the CID correctly from my telco, but when I place the call to the internal analog line, the CID is not propagated. An interesting point: when I try to place a new call to an already bridged line, I see the second call with the CID on the analog phone. The

Hi, I'm trying to get up and running a TDM400 with a standard italian pots line but i'm having problems at getting asterisk to detect when the line get answered on outgoing calls. I'm using asterisk 1.6 beta 9 with zaptel 1.4.11. I tried with and without answeronpolarityswitch=yes but it didn't change anything at all. With callprogress=yes answer get never detected. With

I have a TDM400 with an FXS and FXO interface. I have adjusted the TX and RX gain for both the FXS and FXO channels so that everything is balanced. I hear myself very loudly with no lag. I also get alot of background noise when the bridge is formed between the FXS and FXO channels. I have read the following articles: http://www.voip-info.org/wiki/view/Asterisk+echo+cancellation

Hi all, I found that there will be a memory leak if asterisk running day by day without restart. Is it good to restart asterisk service daily? What is the better way to restart it daily like apache? ango

Hi all, I am looking for a prepaid application. I found that there are many applications in the page http://www.voip-info.org/wiki/view/Asterisk+Prepaid+Applications. Anyone recommendation among them? ango