similar to: Two PRI setup questions

Displaying 20 results from an estimated 10000 matches similar to: "Two PRI setup questions"

2006 Apr 27
5
PRI configuration
Hi, I am getting this message on the * console on my first pri span. Pri show span show it is down, and I can't make any calls from the span. Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27 07:40:23 NOTICE[23988]: chan_zap.c:8202 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Apr 27
2006 Oct 08
5
PRI issues
Hey everybody, I've, within the last 3 weeks, moved over to a PRI from SBC/AT&T. I've received several complaints about dropped calls. Reviewing the archives on PRI and dropped calls shows that I should set the resetinterval=never in the zapata.conf and restart. This hasn't helped. The dropped calls have to date only been on outbound calls. Usually within 2 to 3 minutes
2007 Aug 06
4
low-level dump for PRI dchan debugging
I've been going back and forth with my telco for several days, trying different configurations to get a new PRI to come up. The bchannels are all up and the T1 is not in alarm status. The dchannel refuses to come up however. We've tried ni2, qsig, and now dms100 for the switchtype. The telco tech I've been working with says that he's been sending "reset all channels"
2009 Aug 12
3
Creating an IAX/SIP-to-ISDN PRI gateway
Hi all, I'd like to setup a really lean Asterisk installation that essentially has a full ISDN PRI (AT&T, T1, 23 B-chans, 1 D-chan, BZ8S, 5ESS, National dialplan) on a Digium TE207P adapter that all it does is convert the ISDN channels to SIP/IAX channels. Then I would add this Asterisk 'gateway' as a provider on one (or many) Asterisk systems on the back. With such a config I
2011 Aug 16
1
PRI Problem
I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS
2003 Apr 09
6
Configuring for outbound calls with PRI on T100P
I run a SIP-only shop with a 23 channel PRI and single T100P. Here are my configs: /etc/zaptel.conf: span=1,0,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us /etc/asterisk/zapata.conf [channels] context=default switchtype=dms100 signalling=pri_cpe pridialplan=unknown rxwink=300 ; Atlas seems to use long (250ms) winks usecallerid=no hidecallerid=no callwaiting=no
2005 May 16
1
2 servers via PRI
Good day all How do i set a connection between 2 asterisk servers via PRI In Bri I would set one to NT and TE How shoud the zapata.conf and zaptel.conf look And how should the cable be? All I got on the web was to set one to "pri_net"...this cant be all? And the cable > pin1 <--> pin4> pin2 <--> pin5> pin3 <--> pin6> pin4 <--> pin1> pin5 <-->
2007 Mar 20
2
Problem with "AT&T Maintenance" protocol in PRI connection, no B+D channels available
Hi guys, We are experiencing a problem with a T1 PRI connection. After trying a number of variations in the configuration files, the behavior is always the same: no B channels come up and the D channel doesn't appear to be working well. We can see there are AT&T Maintenance messages being exchanged by asterisk and the provider, CONNECT and CONNECT ACKNOWLEDGE, but that doesn't
2006 Mar 22
3
PRI DMS100 -> Nortel Meridian Option 81
Hello all, I have Asterisk 1.2.1 and a TE110P connected to a Nortel Meridian Option 81C system. The PRI line is currently setup as DMS100. Here are the relevant lines from zaptel.conf and zapata.conf: zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone = us zapata.conf: [channels] language=en context=from-internal musiconhold=default switchtype=dms100
2005 Feb 11
2
Question about DID
Hello Group I have a Asterisk server running with 2 Digium T1 cards installed. 1 card connects to Telco via a PRI. The 2nd card is connected to a fax server via Digi DataFire RAS 24 PT1 Adapter (Digi0001). The idea is to have Asterisk route the calls based on DID or FAX tones. Everything is working great so far. The only problem is the Fax server does not see the DID. How can I tell if Asterisk
2004 Jul 03
1
Caller ID and DNIS Problems (Non-Pri T1)
I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800
2004 Dec 03
3
Two zaptel T1 cards: no clock from one
List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to
2004 Nov 29
1
New T100P Pri install suggestions?
In the next week or so, we'll be turning up a new T1 Pri from Cox Cable in Omaha using a T100P (installed but not yet configured). While discussing the interface parameters with a very knowledgable Cox engineer, we decided on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits of called number forwarded to *, and switchtype=national (NI2). They indicated their CO switch is a
2005 Apr 22
4
TE11OP -> Mitel 200Sx??
Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24
2005 Sep 28
2
Sep 28 00:42:35 ERROR[5151] chan_zap.c: Unkn own signalling method 'pri_net'
Did you compile and install libpri *before* Asterisk? I had same problem (among others) b/c I didn't install in the correct order. Try the awesome asterisk_update.sh shell script. Are you trying to emulate CPE or NET? Try signalling=pri_cpe Check for whitespace behind the statement, zapata.conf seems bitchy about whitespace. hth -----Original Message----- From: Steve Totaro
2005 Jun 14
2
[PRI] TE110P
We are in the process of installing a PRI line and we are going to connect it to an Asterisk Box. Verizon called us today to find out some information. I am surprised that they have never heard of Asterisk or Digium. But anyways, they needed some information in order to set up the circuit. Does the TE110P support NI1 or NI2? (I think the answer is both) What is the number of digits
2006 Apr 10
4
callerid name inboune from PRI
I switched PRI vendors recently, and one of my questions was "do you provide caller ID name in addition to number?" AT&T Local did not, But XO communications said they did. Before I call to complain, is there an setting to turn this on in asterisk? I want to make sure that I have my side covered before I call XO. My current zaptel.conf is: context=from-pstn switchtype=national
2008 Mar 03
2
T1, Rhino, & Nortel
Hi all, I'm trying to insert a Rhino Ceros box equipped with a Rhino R2T1 dual-T1 card and running the latest version of Trixbox (2.4.2) between the central office and a Nortel Option 11. The switch at the CO is a DMS100. Basically, I'm taking the T1, connecting it to port 0 on the R2T1 card, and then connecting port 1 to the Nortel. (Actually a CSU and then the Nortel) We're running
2009 May 20
2
asterisk crash on DAHDI error: No more room in scheduler
Hi, I'm getting the following error from an asterisk 1.6.0.9 installation: [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: Asked to delete sched id -1??? [May 20 06:07:18] ERROR[18517]: chan_dahdi.c:10515 dahdi_pri_error: No more room in scheduler This repeats a few times, then asterisk crashes. I can't seem to locate any info on this error at all. I'm using
2005 Sep 28
1
Sep 28 00:42:35 ERROR[5151] chan_zap.c: Unknown signalling method 'pri_net'
Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing