similar to: Problem with flash hook

I would just like to follow-up on the ringback problem I'm getting from *. As I've said in my previous post, I am not hearing the "real ringback" from the Cisco gateway terminating my call. I don't want to provide false ringback from * (r option of dial), because it'll still give me ringback even if I am suppose to hear announcement or fastbusy. Below is captured ISDN

Hi all, I am seeing on my logs this message: Jun 13 09:14:51 DEBUG[4944] chan_zap.c: Monitor doohicky got event Event 160 on channel 3 Jun 13 09:14:51 DEBUG[4944] chan_zap.c: Monitor doohicky got event Event 160 on channel 3 (repeated much more then what I will show here). I see that it comes from static void* do_monitor(void *data) in chan_zap.c, but I do not understand what does it

hi all, i have an asterisk install with a digium 4 port fxo card and cisco 7960 sip phones -- running on a compaq Pentium III (Coppermine) at 800Mhz 256KB cache and 1GB of ram. when a call comes in on zap/1-1 for example, the delay between when zap sees the line going to ring state, and when the desktop telephone rings can be as long as 7000 milliseconds (or about 3 or 4 rings on an ear piece).

I have the following setup: DS3 -> Cisco AS5400 -> H.323 (ooh323) -> Asterisk Inbound calls work great but outbound calls fail. So to check and make sure we have outbound calling ability on the DS3 we setup a Cisco Call Manager Express and it can make outbound calls both local and long distance with no problems. The failure code is Cause i = 0x8381 - Unallocated/unassigned number. We

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Howdy, New installation, trying to connect an RBS T1 with AMI/D4 framing and E&M Wink. Using a Sangoma A102d and asterisk 1.4.22-2 on Centos5 (Trixbox 2.6.2.1). Outbound calls work fine, but inbound calls fail to read the DID information, and with debug set to 10 I get the following: [Feb 2 19:40:23] DEBUG[25184] chan_zap.c: Monitor doohicky got event Wink/Flash on channel 3 [Feb 2

Hello, my configuration is the following: a TDM400P board with an fxs and fxo daughter boards on it. I thus connect a fax to my FXS port, after having verified that this port was correctly functioning. For this, I had tried before with a simple phone, and with some basic voicemail exten scripts. Here is my simple dialplan for my fax reception: exten => 300,1,Ringing() exten =>

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

Hi list, Just installed spandsp. In my limiting testing, I have an issue on a Philips fax machine (HFC21) directly connected to my * server through TDM400, reception with rxfax works fine, but txfax always fails. Below is a transcript of failed transmit. This is with asterisk-1.0.3 (with native moh patch but I don't think it is the source of the problem). I already tried libtiff 3.5.7,

Hi, I have a problem that is biting at all my customer sites where they have PRIs taking heavy load. This happens both with the stable code stream and with the current CVS. What happens is that after some running, Asterisk starts reporting strange errors on the PRI, eventually calling the PRI down Starts with this sort of thing: Feb 21 09:39:23 DEBUG[18095]: Didn't get a frame from

I have been trying to sort this out for a while now but with no luck I have isdn <-> asterisk<-> pabx on a te205 incoming calls work fine outgoing calls seem to work fine but the call is dropped when answered I think it is to do with the line [May 8 17:51:55] WARNING[4762] channel.c: Unexpected control subclass '5' that is causing the problem but I don't know how to

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

I'd like to have my Asterisk system pick up a certain extension on an existing Panasonic PBX when it rings. (It's connected to some proprietary Panasonic doorphones that I haven't replaced yet.) I connected that extension to an FXO port on a Digium AEX410 card, and set that channel to have the context "doorphone". The problem is that the extension is never executed. With

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

Hi all, I need to test the significnce of difference between slopes of two regression lines and regression line with theoretical line. I try to use Slope.test function from emu package, but an error occured... library(emu) d1<-data.frame(P1=c(1,2,3,5,7,8,9,13,14,15), P2=c(1,2,5,8,11,13,15,15,18,24), R=c(2,7,8,9,16,21,27,31,33,36)) # First data set m1<-lm(R~P1+P2+P1*P2,data=d1) # Regr.

I'm considering switching my incoming phones lines from standard analog to a T-1 service from XO communications. They propose to bring in an "IAD" which has 12 lines of voice and 768k of internet bandwidth as part of a package deal. Since I want to keep the voice traffic in the digital domain the equipment they're proposing is a "Lucent Digital Vina Integrator" IAD

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

Hi, For MGCP users. Is there any success stories with any MGCP IAD vendor. I?m trying to find an IAD which works with Asterisk. I?ve tried the Cisco IAD 2430 without success; but SIP on this IAD works but it?s limited (no authentication, no notify messages, etc) and with higher density IAD (16 or more ports) it?s nice to control using MGCP. Any information will be apreciated ! Thanks. --

Hello, I have a cisco ATA 188 registering both of its lines to * I can place calls between then an to kphone an MSN messenger (both registering with * too), a few days ago a friend lend me a Cisco IAD 2430 and I was willing to do the same thing with it, since it has 24 ports I was willing to to use 24 analog phones with it however something really weird happens I can place calls from my ata,