similar to: Correct voltages but no dial tone on TDM2400P

Hi, I have a problem with TDM2400P card. The card is detected ok, I can make a call but only with pulse dialing (not tone dialing) without hear sounds from the headset. When I receive a call, I can to establish a communication, but without hear sounds from the headset. When I dial any phone key, I can hear dtmf tone. I'm using Elastix 1.5.2. These are my configuration files:

Hi, I'd like to change 3 TDM400p with one TDM2400p to avoid echo (my intention is to use a TDM2400P echo cancel module). It TDM2400p working good with asterisk 1.2.1? Or I need to install a new asterisk version? TIA Giorgio Incantalupo

Hi i have a tdm2400p and installed asterisk 1.4.11 with zaptel 1.4.5 im having an error message when in running asterisk with the tdm card in. here's the error from the console of asterisk: [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:7489 mkintf: Unable to get span status: Inappropriate ioctl for device [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:10466 build_channels: Unable to register channel

Hello, Thank you for your support of Digium and Asterisk. Yesterday, we identified a problem with the driver for the TDM2400P card when used with FXO port modules. The X400M was producing (and expecting) the audio signal at an abnormally high level, which negatively impacted the performance of the echo cancelers, both hardware and software. It also resulted in unusual audio artifacts when the

Hi All, I have the problem with TDM2414E card (16FXO & 4 FXS with echo cancellation). I have already connected to the asterisk server and loaded wctdm24xxp module. When I connect the phone to FXS port, It gets the dial tone but I cannot dial to any number (I can press the phone button but nothing happens even the busy tone). There is no activity in the asterisk CLI. It just prints

For example, how much power would a server with 3 of the TDM2400P fully loaded cards draw? We're trying to figure out what APC power we should have to achieve approx 30 minutes back-up time. Would appreciate any learnings or methods on calculating the power draw and determining the appropriate back-up device. Thank you. Melisa.

I am having issues with a TDM2400P. It appears when the ZAP channel dials out, it randomly chops the first digit off of the number. I have tried relaxdtmf=yes, turning up and down the txgain, turned off and on the echo cancellation, generated new zaptel (with updated spinlock.h)... I am at a loss. Can someone please offer some help? Thanks. TJ

Hi list, I have this problem: when someone is making a call, with asterisk and a TDM2400P connected to 8 fxo lines, the sound is good, but if three, for people are calling at the same time the sound got worse and worse. Using other voip cards the sound is much better even with all user calling at the same time. What can be, the problem? Someone else has having the same

Hi, I cannot make my TDM2400P (with Echo Canceller module) detect faxes. I tried with a TDM400P and it worked at 80% (20% of faxes were lost). My test conf.files are: _zapata.conf_: context = inbound faxdetect = incoming language = it musiconhold = default signalling = fxs_ks callerid = "call_or_fax" channel => 1 extensions.conf: [inbound] exten => s,1,Answer exten =>

Do the zaptel drivers need to be told >NOT< to use the software echo canceller when using a TDM2400p card with hardware echo canceller, or does the driver figure this out by itself? Thanks, Andrew -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061117/7dc52295/attachment.htm

Hello, We've purchased a 2nd Wildcard TDM2400P for our asterisk server. I've looked around but I can't find documentation on how to properly setup 2 or more telephony boards in asterisk. In particular, I want to ensure that the boards are assigned the same device channels on boot (for example, if you have two NICs in a Linux box and you want to make sure one card is always eth0

Hi, I have a box with Debian Sarge, Asterisk 1.2.1 (and zaptel 1.2.1) and a TDM2400P with echo canceller. I installed the card but no echo cancellation is being made...seems like the echo canceller module does not work, infact the software cancellation is working. My zapata.conf has echocancel = 128 and echocancelwhenbridged = yes but no echotraining parameter which gives a warning. I found

We just bougth a tdm2400p with all the modules for FXO, but we are having some troubles with the card, cause it aparently is stripping some digits from the dialed number, we tested the same server with a tdm400 and everything worked as expected. We?ve already added "w" before the dialed number with no results, is there any way to solve, is it a bug thanks

Hi all, I'm confused, in digium website, it says: TDM2400P: It supports a combination of up to 6 FXS and/or FXO modules for a total of 24 lines. 6 plus 6 is 12, how come it's 24? if I have 24 PSTN lines, i'll be needing 24 FXOs. Pls. elaborate. thanks. Lito -------------- next part -------------- An HTML attachment was scrubbed... URL:

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hi: I?Bought TDM2400P ,with 24 FXO ports , I installed? the asterisk 1.4.28 and?dahdi 2.2.0?and then i compiled them and configured all, i pluged into 8 pstn line into the Rj connector and then i got messages on asterisk console that alarm cleared on channels 1->8??, at this step everything should go fine ,but when i try to make a call?through the TDM?there is silence and no audio,and then i

How many TDM2400P cards can I safelly install in one PC? I'm loking for answers from whoever has a working scenario with * and a number of cards higher than one. Thx, Juan __________________________________________________________ Mensagem enviada usando o Webmail da ViaLink ver. 2.7.8

Hi Francois, Thank you for your interest. I tried the card alone so I don't think is an IRQ problem (anyway is there a way to be sure?) To be sincere, in all systems I saw (even working ones) there is an IRQ balance failed where Linux boots. The system is new, I tried different processors (P4 and Celeron) with SMP kernel and without. The card has the echo module, could not be

Hello All, I'm looking to get some feedback on which solution of providing FXS is going to have the best results with faxing. I'm only looking to see what method is going to provide the best digitization into Asterisk, not for transmission from Asterisk to else where. Any recommendations of specific channel banks are welcome. I will need to provide approximatly 216 FXS Ports and need

Hi. I am using Digium TDM2400PFXO with Asterisk1.6. When call sets in the box , it answers the call even the phone is not picked. ideally it should answer the call when the phone is picked up. Its charging the clients. Please let me know how can I cover this ? Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL: