similar to: Grandstream GXV-3000

Hello... I have a big problem with asterisk. Every time i make a call asterisk does not bridge the zap channels. The zap channel from which i'm calling remains in state:ring and applicaton:dial and the zap channel with the external line configured remains in state:dialling an Application:AppDial. Zap/20-1 agentie s 1 Dialing AppDial (Outgoing Line) 09399 (None) Zap/9-1 int_omg 09399 5 Ring

Hi List; Can someone advise me why in the below context, it does not run the Background step? Once I dial 1000, then it hangup and give congestion signal? If I comment the ResponseTimeOut, then it run the Background but it does not wait till caller enter the digits, once the sound file finish, then it hangup (congestion signal), also in all the situation, it does not go for the t extension, why?

hi, do you someone test this http://www.grandstream.com/y-gxv3000.htm? video works? (it's have H264 video codec) i want this topology gxv-3000 - nat -{Internet}- Asterisk -{Internet}- nat - gxv-3000 --------------------------------------- Marek Cervenka LCNA - http://lcna.slu.cz =======================================

Dear all I have asterisk setup now what happend when i dial 4 digit number my asterisk wait for few digit why when i press # key it is dialing fast but without # wait for few number is there any configuration for dialplan I have setup asterisk with avaya system i have 5 avaya system on 5 location i use 16XX,22XX,33XX,44XX,20XX to reach avaya extentions but when

I tried to add a couple of SIP phones (polycom 601s) to my existing asterisk installation. I can successfully make a call from the SIP phone to any other phone (inside or outside), but I can not make any calls to a SIP phone. Attached are the pertinent parts of sip.conf and extensions.conf. The log starts off normal with: Mar 26 09:51:15 DEBUG[4885] chan_zap.c: DTMF digit: 2 on Zap/55-1 Mar

Can you post some of your sip configs and your extension configs. Thanks, -gcc -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Ryan Parlee Posted At: Sunday, April 04, 2004 12:10 AM Posted To: Asterisk User Group Conversation: [Asterisk-Users] Asterisk - Cisco 7960 - NAT Subject: [Asterisk-Users] Asterisk -

Hello group, I tried a lot to enlarge the frequency (i.e. more announces, low wait between). according to config, every 30 seconds the announcement should take place. In fact, the first periodic announce is done after 2 minutes? What is my fault? Thank you Regards Paul # zypper if asterisk Loading repository data... Reading installed packages... Information for package asterisk:

Hi all, i am stuck with the configuration of asterisk - modules are loaded ( zaptel and wct4xxp ) - i have zaptel.conf configure, output of ztcfg -vv --- snip -- rapid:~# ztcfg -vv Zaptel Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet

I got four phones: 601 is a SIP phone (no brand) 615 is Snom 190 621 is a Grand stream 628 is a remote SIP phone (no brand) 601, 615, 628 can call each other without any problems 621 used to be able to call remote 628, but after upgrade to CVS Head Nov. 11 the remote party cannot hear me. 615 never could call remote 628, both party hear nothing. 601 can always call 628 [Oct 16 00:52:13] --

Hi Guys, I am not so familiar with asterisk and hope to get help here. I am having now some stupid errors. My goal for the first, is to create a simple pbx with different context. As long as I use only the contex 'default' everything seems to work perfect. Now I tried to add another context i.e 'internal' and the asterisk is complaining for not finding the required extension in

Hi, I have problems while trying to dial from simple analog phone that attached to my TDM400P card. No matter which number i press i immediately get a congestion tone. when calling from outside (e.g cellphone )to the line on port 4 and pressing extension #123 everything works fine and i manage to make a connection. I've plugged on port(Zap) 4 the analog line and on port 1 the phone.

Hi list, We're trying to set up a phone number that customers can call to get a hold of anyone of a group of sysadmins (and not their voice mails!). We found the findme example ([1]) that makes the callees press 1 to accept the call. It almost works, but it doesn't work correctly when one of the callees, the sysadmins, hangs up after accepting the call. We're using this

Has anyone managed to get these two phones to make a video call to each other ? If so, care to share how the hell you managed ? the GXV is at the latest firmware, and xlite the latest download Asterisk 1.4 trunk TIA Julian

I am trying to get a GSM gateway (Alpha Tech GSM Gateway Blue Gate Dual Band Analoog FXO) working with Asterisk. I had a working FXO configuration to a analog port of a small home 1/4 ISDN pbx. I used this same configuration to connect a GSM Gateway that is supposed to be connected to the external(FXO) analog port of a pbx. I can get my configuration to dial the mobile number via the gateway, but

Dear, I'm having problems with the configuration of this gateway(GrandStream GXW 4108), I used the instructions from GrandStream but it doesn't work. Someone has a good configuration for this gateway? Thanks in advance, Nelson -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have Asterisk running with a combination of SIP and H323 clients. I am using the OH323 module instead of the H323 one. When the SIP clients ring each other, they can hear a ringing noise in the ear peice to let them know that the other parties phone is ringing. However, when the H323 client rings a SIP client, there is no ringing sound at all, although as soon as the called party picks up the

Hi all, I have a voice menu system ( Outlined below ), and I'd like to give the user some feedback when they dial an extension ( ringing, music, SOMETHING ). As it stands, when a user enters an extension from the menu system, they hear silence while the line rings. I even tried including the Ringing application before calling my macro to dial the phones, with no luck. Any help is

does anyone have a recorder GSM file that emulates the Telco's "if you are a telemarketer please hangup now" recording? I don't see one in the sounds dir. the ZapATEller works great for computerized callers but if a human hears this message asking them to go away they have to. Isn't that right? Dave

Hi All, i want to configure voice mail on Asterisk 1.4 for multiple users. let me explain you the scenario. i have 10 users with the name of 1000,2000,3000,4000,5000,6000,.......and these user can call to each other. Now i want to configure separate voice mail box for separate user. my extensions.conf ..... settings below.. [voicemail] exten => _X.,1,Dial(SIP/${EXTEN}) exten =>

Hello! I installed NexentaOS (Opensolaris kernel b104+). First booting system is true. Before first rebooting system updates boot_archive. It''s false. Computer is freeze and CapsLock and ScrollLock is blinking. Helps only RESET button. My system is Ubuntu 8.10, kernel-2.6.30-rc3-tip, Xen-3.4-Stable with debug options enabled. My hardware: AMD Athlon64X2 5400+, RAM 4GB. For DomU: mem=1024,