similar to: bristuff: music on hold but no dialoptions tT defined.

Hello again, I am using mix monitor and the majority of the sound records perfectly. I then get a "Internal Data Stream Error" near the end of the sound file. Has anyone ever seen this? I am allowing the ULAW amd ALAW codecs and an example dialplan entry is ; ; phone line phone1 exten => phone1,1,Answer() exten => phone1,2,MixMonitor(test.wav|av(0)V(0)) exten =>

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hi. I'm trying to get a Beronet QuadBRI card work with bristuff drivers. Though qozap module loads right, all card spans are in deactivated status. I'm quite sure my configuration is correct and using a single BRI card instead of the quadBRI the status is active and I can place and receive calls. On Beronet installation manual I read that Beronet and Junghanns cards are identical in

Hi, Reading from www.voip-info.org, i can see that "Junghann's chan_capi is now part of bristuff <http://www.voip-info.org/wiki/view/Bristuff> , as of version 0.3.0-pre". What does that really mean ? Shall I understand I can share a Junghanns QuadBRI board between 2 CAPI-enabled software (like a 0.3.0-pre bristuffed Asterisk for instance) ? If positive, what are the pros and

Hi- we are having issues with quadBRI card which does not work together with TDM400P. We've tried to hunt the problem and here is the scenario: 1) starting asterisk with tdm400P and two FXS modules (two phones) 2) pickup first phone and dial the second one works great 3) hangup 4) pickup second phone and tried to dial the first phone - no luck - asterisk does not recognize DTMF of the

Hello, for a long time I've been having problems with analog modems and faxes communicationg over ISDN BRI lines. Now I began to suspect that this is due to * being out of sync with the PSTN. I have a quadBRI card with first two ports connected to PSTN, and defined as follows: span=1,1,0,ccs,ami span=2,2,0,ccs,ami This should mean that spans 1 and 2 are used as primary and secondary

Hi all, I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns QuadBRI running in NT-mode. Connected to the BRI-Ports are 12 Fax-Modems (Elsa MicroLink ISDN/TL V.34) which are only operating in dial out analog mode to deliver fax messages. After a while of running fine (50-200 dial out connections) on some S0 spans the following message occurs

Does anyone test Asterisk 1.2.X + bristuff-0.3.X and TDM card? We can't get it to work. -David -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Julian J. M. Sent: Friday, March 31, 2006 1:44 AM To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Re: BRI

Again trouble compiling bristuff-0.3.0-PRE-1q with the florz patch on a x86_64 box (I guess nobody is using x86_64 platform or is able to fix this themselves?) First of all when bristuff is downloaded and compile is started it appears that the bristuff Makefiles are badly broken. The asterisk Makefiles all do see to find the kernel sources on a RHEL4 box in the proper directory, the pure

Hi Alessio Yes, the problems you report do seem similar to the issues I had. I found on the Dells that the audio prompts were very choppy and played slower than normal. Occasionally there would be 'bursts' oav a second or so of 'good' audio. I also suspected IRQ issues but the Dell Mobos had no way of adjusting them. Best thing is to try and get the card on its own unshared

Hi, it helps to have configured and working kernel sources installed. Configure your kernel sources for the running kernel and then run "make" in the kernel source dir to build the necessary scripts. You dont have to wait until the kernel is compiled. best regards Klaus -- Klaus-Peter Junghanns Am Samstag, den 25.06.2005, 02:45 +0200 schrieb Stefan Gofferje: > Hi folks, > >

Hi, I had problems described in another thread so went from a start, but now have problems when loading qozap module. I get : # insmod qozap.ko ports=9 insmod: error inserting 'qozap.ko': -1 Unknown symbol in module and in /var/log/messages: module qozap unsupported by SUSE/Novell, tainting kernel. qozap: disagrees about version of symbol zt_receive qozap: Unknown symbol zt_receive

Hi Kape, Life is generally good with bristuff and the quadBRI cards. However I've got a concern: how does one return a busy signal to the telco when all B channels are busy? Right now, when all channels are in use, the remote caller is kept waiting until the telco times out and finally get a busy signal (on a land line) or error tone (mobile). On the asterisk side here is the output: --

Hi all, Using Asterisk 1.0.10-BRIstuffed-0.2.0-RC8q with a Junghanns quadBRI (2 spans connected) and a Digium TDM400 for extensions Shouuld I be worried about these lines that keep showing up in my /var/log/messages? qozap: dropped audio card 1 cardid 0 bytes 6 z1 10 z2 116 qozap: dropped audio card 1 cardid 0 bytes 6 z1 50 z2 28 qozap: dropped audio card 1 cardid 0 bytes 6 z1 59 z2 37 .. ....

Hello, I have a Gigaset S44 connected to a quadBRI NT port. Receiving calls works phone, however when dialing out from the phone the call is dropped to the 's' extension, as if no extension had been dialed: -- Accepting voice call from '492389990' to 's' on channel 0/2, span 4 -- Executing Directory("Zap/11-1", "default") in new stack --

Hi, I have the SuSe9.2 installed in a box with a QuadBri. I have followed all the instructions i have found and this is my best result... only one error compiling zaptel :( .. y have the kernel sources an already made the links to its drwxr-xr-x 8 root root 328 Jun 16 20:20 . drwxr-xr-x 12 root root 320 Jun 16 14:05 .. drwxr-xr-x 3 root root 136 Jun 16 20:17 asterisk drwxr-xr-x 22 root

Thanks. I think our problem ca be similar. Have you tried to call from analog phone #1 to another analog phone #2? It works. But when you try to call vice versa from #2 to #1 it does not work. When you restart asterisk it works again - but only one direction. -David ________________________________ From: asterisk-users-bounces@lists.digium.com

>Hi All, > >I'm using Asterisk 1.2.17 and I would like to install BRIstuff. Problem is >that current version of BRIstuff is for Asterisk 1.2.14. > >BRIstuff 0.3.0-PRE-1y (* 1.2.14) > >If I'm misunderstanding how to apply patches for 1.2.17? > > >Thank you in advance, > >Dominik I found it:)

Hi All, I'm using Asterisk 1.2.17 and I would like to install BRIstuff. Problem is that current version of BRIstuff is for Asterisk 1.2.14. BRIstuff 0.3.0-PRE-1y (* 1.2.14) If I'm misunderstanding how to apply patches for 1.2.17? Thank you in advance, Dominik