similar to: Asterisk using 200% CPU and then crashing...

Does anyone know if the Dell Power Edge 1900 has an issue with multiport E1 cards? We've had this server running for a while now with 2 E1 cards. At first we tried to install an Openvox D210P card with two E1 ports but after a couple of kernel panics we thought that maybe the card was defective and we replaced it with two Digium TE120P cards. Now the customer needs a third E1 port and

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

Here is the scenario: Asterisk 1.14.13; zaptel 1.4.6; Digium TE120P (same problem with various previous versions; same problem with different TE120P cards). The customer has a partial (10 B-Channel) PRI that when it is busy (eight or more B channels in use), tends to fail as shown below... [Jan 26 23:00:31] ERROR[31893] chan_zap.c: Write to 28 failed: Unknown error 500 [Jan 26 23:00:31]

Hi, I am facing problem in configuring D-channel for TE120P card.I did the following things /etc/zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 /etc/asterisk/zaptel.conf group=1 signalling=pri_cpe

Hello List, I just have a query.... is it possible to have 2 or more telephone number mapped to the same E1 line and if so will the TE120P card pick up the last 4 digits of each number - as it is currently doing for the one? -- Kind Regards Etienne Pretorius -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, We are using - a dell sc440(Single dual-core intel xeon 3040, 1.86GHz,1066MHz front size bus 2MB cache) as the asterisk server - dell 400sc(Intel P4) as a SER server - digium isdn card, TE120P at Asterisk server - Bandwidth: 2Mbps/512kbps All SIP Phones are registered to SER server, and SER will route all outgoing calls to Asterisk server. My problem is the sound quality goes down if

Hi all, Can anybody tell me that wether I should install DIGIUM-TE120P card on redhat9.0 2.4.20-8 or 2.6.18 kernel. I am using kernel 2.6.18 but facing a very serious problem of modutils and iptable. Can anybody help me out. Thanx and Regards sanchal singh

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

I have a brand new TE120P card that I have installed and asterisk is not starting as I am getting the error: ERROR[5054] chan_zap.c: Unknown signalling method 'pri_cpe' It seems it does not matter what I change the vaule for signalling= to, it always returns it as invalid. I have tried the config from my other 2 servers running TE110P cards and the config from AusTechPartniships

Hi all I use asterisk (1.2 brach) from debian official packages and it works fine. Now I need to install and configure a Digium TE120P card, but I cannot find any guide to install it using debian packages. I would like to know if anyone of you knows about packages that would include the necessary kernel modules or any other method that won't be broken when the asterisk packages are updated.

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

Hi List, I am from Peru, I have installed an asterisk server in my company with digium card E1 TE120P, I am having issues when i make calls, here the error from my server [Oct 18 09:13:50] WARNING[2377]: channel.c:3232 ast_request: No channel type registered for 'Zap' [Oct 18 09:13:50] WARNING[2377]: app_dial.c:1106 dial_exec_full: Unable to create channel of type 'Zap' (cause

Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

Hey Everyone, I would like to start testing/playing with PRI channels but I don't have access to a PRI line. Is it possible to do the equivilent of a crossover between two PRI Cards (say Digium's TE120P)? What I was thinking is that I could set one asterisk box up with a PRI card set as the TE and provide clocking and another box exactly the same but with the card setup as NT. I think

Hi, all I want to configure a few FXS ports in an Antribank-16 to be able to receive faxes sent throught a PRI: E1 ==>Zap * ==>FXS * ==>Fax machine My asterisk box has a Digium TE120P (for the PRI). Versions are *=> 1.4.17 | Zaptel=>1.4.8 | libpri=>1.4.5 The Astribank is not configured yet, because I am a little bit confused about how to do it. Let's say I configure

Hi I posted earlier about having issues connecting to Telewest's ISDN, only to find out later Telewest had forgotten to turn it on - hopefully I'm not having a similar silly problem. My PRI span is now up and operational, but when I try to send a call out over it, I just get congestion tones. Occasionally, I get about one second of ring tones, only for it to cut out and play congestion.

Still trying to upgrade to 1.6.0.9 for 1.4. It worked - it worked all day yesterday, but this morning: -- Executing [646xxxyyyy at longdistance:1] Answer("SIP/172-08276a60", "") in new stack .......... -- Executing [646xxxyyy at longdistance:6] Dial("SIP/172-08276a60", ""DAHDI/g2"/1646xxxyyyy") in new stack May 27 09:56:57]

Hi, My asterisk server was working with a 4-FXO analog card (TDM400P). I recently added two digital cards: a TE120P (1 PRI) and a B410P (4 BRI). The B410P is still unconfigured but inserted in a PCI slot. The TE120P's jumper is set to E1 as it will connect to a commercial PBX's PRI card also configured as E1. My analog channels used to be 1-4 but since I added the new cards I changed

I'm trying to upgrade from 1.4.24.1 to 1.6.0.9 with a TE120P card. I can't make any connection over the T1. From CLI: ERROR[26017]: chan_dahdi.c:14300 process_dahdi: Unknown signalling method 'pri_cpe' at line 37. cat chan_dahdi.conf cat chan_dahdi.conf [trunkgroups] [channels] language=en ;internationalprefix = 00 ;nationalprefix = 0 context=from-pstn switchtype=national