similar to: Problems Connecting Two Asterisk Installs ViaISDN PRI Cards

I am trying to connect two machines to each other with an T1 crossover cable. The first machine has two TE120P cards - one connecting to the telco on an ISDN PRI. The second to a crossover T1 cable to a second machine which has one TE120P card. Telco <-cA-> Machine1 <-cB-> Machine2 Machine1: Two TE120P cards Machine2: One TE120P card cA: Standard T1 Cable cB: Crossover T1

Hello, I'm having issues connecting throu PRI with the following error "Requested transfer capability: 0x00 - SPEECH" Below are the logs: == Using SIP RTP CoS mark 5 -- Executing [97052660 at voipphones:1] Set("SIP/4856-00000003", "CALLERID(num)=xxxxxxxxx") in new stack -- Executing [97052660 at voipphones:2] Dial("SIP/4856-00000003",

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing

List, I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel bank). I cannot seem to get the T100P to send any clock to the channel bank. I prefer that it use the same clock source as the TE410P, but it doesn't matter if it's not in sync just as long as it's there. The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to XO Sonus switch, the net to

Did you compile and install libpri *before* Asterisk? I had same problem (among others) b/c I didn't install in the correct order. Try the awesome asterisk_update.sh shell script. Are you trying to emulate CPE or NET? Try signalling=pri_cpe Check for whitespace behind the statement, zapata.conf seems bitchy about whitespace. hth -----Original Message----- From: Steve Totaro

I have just built a new system using an HP DL360G7 with a TE420 T1 card, and this is the first system using a generation 7 server. I'm not sure whether that is an issue or not. I am using Asterisk 1.2, and Zaptel 1.4.12.1 with patches for GEN5 of the TE420 card. I have successfully used this combination on several systems based on the DL360G6 and TE420(gen5), which have been in production for

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

Hello, I'm fairly new to asterisk and Trixbox, I'm setting up a Trixbox based email to fax gateway. At this time, I have a ZAP PRI link between the eFax server and my VoIPSwitch. The ZAP channels are configured, the B and D channels are up, and I have green link lights on either end of my cabling, but when I dial the number I have assigned to my eFax server, the call never seems to route

Good Day All, I am experiencing some weirdness using the E&M channel and hope you can offer a little assistance with the problem I am having. 1) call comes into channel 25 (Second Span first channel of a Digium Quad PRI from SBC-PRI) 2) Call is sent to channel 1 (First Span first channel on the Digium Quad PRI connecting an ADTRAN via E&M Feature Group D) 3) Between rings one and two

Hey, Thanks for the input Andrew. I did all you suggested but noticed that when I did the loopback test, the output *was not* there as you mentioned ("I'm set to pri_net, but the other side thinks it is pri_net!"). In fact, the same message as before kept repeating every second or so: >> Unnumbered frame: >> SAPI: 00 C/R: 0 EA: 0 >> TEI: 000 EA: 1

---------- Forwarded message ---------- Date: Tue, 4 Jan 2005 17:12:32 -0800 From: Bill D'Anjou <danjou@rocketinternet.net> To: steve@daviesfam.org Subject: FW: [Asterisk-Users] TE410P card in an HP-Compaq DL380 G4 server Can you post this to the group for me? I've joined & I am receiving e-mails from the group but when I try to post I get a bounce saying "waiting for

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

I have TE405P span connected to a patton/digi 2977 T1/PRI port. Zaptel starts up fine without any errors. Libpri is installed as well. But I get the following when trying to load asterisk ------- Jul 3 19:30:26 ERROR[8192]: Signalling requested is PRI Signalling but line is in Unknown signalling 896 signalling Jul 3 19:30:26 ERROR[8192]: Unable to register channel '25-48' Jul

Hi, I have two t100p cards installed. One card connected to the PSTN, the other card is hooked to the Definity PBX with a T1 cross over cable. The card connected to the PSTN works fine. The problem is with the card hooked up to the PBX. The light behind the card is green, but when I dial from this card I get an error. Its says it could start the D-Channel. Could someone help me out with this

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

Folks, I recently swapped a TDM400 FXS card that was working perfectly into a new server (running recent CVS), and it's either misbehaving (unlikely), or I've missed something obvious (much more probable). Everything seems to be working, but I can't get any dialtone from it when I plug a phone into any of the 4 ports!! All of the jacks are lit (green lights) but they all seem dead

I set up a TE405P to go T1---*---Toshiba. I have the channels configured, and can place calls from the Toshiba, through * to the t1. Incoming calls work great to *, but if they go to the Toshiba, I get a hangup. I think the * is sending the call to the wrong span. I have 2 spans, span 1 from the T1, span 2 to the Toshiba. The bchannels show as 0/1 through 0/23 on both spans in * when it starts.

I have a two port TE205P Digium card. I have set everything up to create a native zap bridge between the two spans. Everything works perfectly except one thing. Our telco has a "password" that has to be entered as soon as a long distance call is made. So if I dial a long distance call from my meridian system, asterisk bridges the call between two channels, my telco picks up and gives

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as