similar to: Astribank and caller ID from PSTN

I'm getting this messages trying to call with one sip trunk: Feb 3 16:43:09 DEBUG[3389] channel.c: Avoiding initial deadlock for 'SIP/usa-e2ea' Feb 3 16:43:09 VERBOSE[3491] logger.c: -- SIP/usa-e2ea answered Zap/1-1 Feb 3 16:43:09 WARNING[3491] channel.c: No path to translate from Zap/1-1(68) to SIP/usa-e2ea(256) Feb 3 16:43:09 WARNING[3491] app_dial.c: Had to drop call

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

H all... I have an Astribank (8FXS/16FXO), IBM X3200 M2, Asterisk-1.6.2.1, dahdi-linux-complete-2.2.1, libpri-1.4.10.2, centos-5.4 final. My problem is, every time i unplug the astribank power supply, and reconnect it, astribank cannot work again (lsusb result is 11x0)... but, after reinstall the asterisk and dahdi, astribank will detected (lsusb result is 11x2)... any suggestion? Regard,

Hello, Can you recommend a good billing software for asterisk that supports reseller accounts? Will be better if it haves opensource licence. Best regards, -- Guillermo Salas M. Telconet S.A. Calle 15 y Avenida 24 Esq Edificio Barre #2 Primer Piso Telefono : +593 5 262 8071 Celular : +593 9 985 5138 e-mail : gsalas@manta.telconet.net www : http://www.manta.telconet.net

Hi, I'm trying to make ooh323 works with one asterisk box running 1.2.15 version. I can ring from a h.323 to SIP and SIP to H.323, but when the call is finished when the phone is answered. This is the log when I call from the H.323 device to a SIP device: Feb 23 10:57:32 VERBOSE[6096] logger.c: -- Executing Dial("OOH323/Telconet Mantaer-c5f8", "SIP/666|30|TtrwWC")

Hi Guys, An 8 channel Astribank is connected to Trixbox 2.8 and I ran freepbx-module-zapauto but I get the following when running these commands and can't make calls out: [Trixbox]# dahdi_genconf xpporder /usr/sbin/dahdi_genconf: warning - OLD DRIVER: missing '/sys/bus/xpds/devices/00:0:0/timing_priority'. Fall back to /proc pbx*CLI> dahdi show channels Chan Extension Context

Hello, I recently got a problem I have never seen during my previous installations. I have a Xorcom device with 4 BRI and 8 FXS ports. I use ubuntu Linux and asterisk 1.4.22. Everything works fine but after some time zap channels disappear in asterisk. root at pbx1:~# cat /proc/zaptel/* Span 1: XBUS-00/XPD-00 "Xorcom XPD #00/00: BRI_TE" AMI/CCS NOTOPEN 1 XPP_BRI_TE/00/00/0 Clear

Hi all. Done some research, Googled a lot, but can't find out if there is a USB FXO adapter that works well with Asterisk. If someone knows of one or has used one, I'd be very interested to hear about it. Many thanks, Nathan -- -------------------- www.nathanpralle.com --------------------

Hi, I'm having some trouble setting up a Xorcom Bri 4 port. I have compiled asterisk and zaptel using the Bristuff bristuff-0.3.0-PRE-1y-g patches. So I'm running zaptel-1.2.17.1 and asterisk-1.2.18. The problem I'm having is that for one I get no LEDs showing if the unit is in TE and NT mode (not a issue for me but may have some impact on things) I have no errors in any logs I

Hi, I've asterisk-oh323 0.7.3 and after 2 days of test finally I can make calls from one h.323 device to the world using sip trunks :) I can call to sip devices from the h.323 one. Now I want to make calls from sip to h.323 but it does not work. Maybe one of us have a configuration example to do this? I'm using the latest svn version (compiled yesterday).

Hi, Anyone is using LG ip phone LIP-100 with Asterisk. I've two of this phones but seems to work only with net2phone, in the product page http://isupport.lge.co.kr/html/ibu_lgic_modelView.jsp?jgrcode=D2_IPTP&modelid=M_IP100C the features are showing SIP and H.323 support. Can be used with my asterisk box? Best regards, -- Guillermo Salas M. Telconet S.A. Manta Calle 15 y Av. 24 Esq.

Dear Sirs, we ... 1) buy minutes from other providers 2) sell minutes to out clients some calls terminate to our equipment, others - to h323 proxies. we want calls to be routed according to costs (a route is chosen from many by lowest cost). at the end of it, we'd like to bill our clients and see how much have we earned (money we receive from client on one side, money we pay to proxies on

Hello, I have a 4 port FXO digium card with 3 PSTNs attached to it and AsteriskAtHome setup. Everything is working fine except outbound calls. When I dial a outside number, it works fine, but when another employee trys to dial out while I am on a line, it will not go. I have a outgoing route setup in the AMP interface. Dial Pattern: 1NXXNXXXXXX NXXNXXXXXX NXXXXXX Trunk

Hi, I'm trying to compile asterisk 1.2.14 on a Debian Sarge amd64 with kernel 2.6.8-12-amd64-k8 make[2]: Entering directory `/usr/src/asterisk-1.2.14/codecs/gsm' gcc -pipe -Wall -Wstrict-prototypes -Wmissing-prototypes -Wmissing-declarations -g3 -Iinclude -I../include -D_REENTRANT -D_GNU_SOURCE -O6 -fomit-frame-pointer -fPIC -c -DNeedFunctionPrototypes=1 -funroll-loops

asterisk linkedin group I have created an asterisk linkedin group for anyone interested. http://www.linkedin.com/e/gis/45252/66270A773F53 Thank You, Steven BerkHolz - MCSA - MCSE - Manager of Information Systems HIROTEC AMERICA ________________________________ Please visit us on the web at www.hirotecamerica.com HIROTEC AMERICA Ph. 248-836-5100 Fx. 248-836-5101 Please only print this email if

Gang, I recall several months ago that there was a company that was giving away a free 1-port T1 card, with some specific conditions. Do any of you recall who that was? My Google searches are coming up empty and now I'm wondering if I was hallucinating... Thanks, MC -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi: Iam looking for a sip softphone that supports g729 codec Any one have an idea ? Reagrds; jonnyhashem --------------------------------- Don't get soaked. Take a quick peak at the forecast with theYahoo! Search weather shortcut. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello All, I got one quick question on A2Billing. Specs: - - A2Billing v1.3 - OS CentOS 4.5 - Asterisk 1.2 - Zaptel 1.2 Did the installation and everything is working as it suppose to... Using the A2Billing documentation, I created the RateCard, SIP Trunks, and SIP Customers. I was also able to login using XLite Dialer and was able to call out to my SIP Trunk also. Now how can I remove the

Hi, I using asterisk 1.2.4 on a CentOS with Linux 2.6.9-22.0.2.ELsmp kernel. I've two x100p cards connected, only one card is reconigzed by asterisk. 02:01.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 02:02.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip compatible 10/100 Ethernet (rev 31) 02:03.0 Communication controller: Tiger Jet

We have recently install an asterisk solution with about 60 physical extensions. While the system is running it runs reasonably well (Still have a few teething problems) but twice now they have experienced a degradation in voice quality and dropped calls and then finally asterisk completely crashes out. Restarting asterisk will work for a little while and it will crash again, each time less time