similar to: Chan_sip Entry

Hello, I have a small LAN network connected through an Asterisk Server. When I try to make a call between two of the user pc's on this network I get a "401 Unauthorized" error. Would anyone know how to remove the Asterisk Authorization/Authentication? I am not sure if this can be done with an entry into the sip.conf file, or by other means. My sip.conf file is shown below: ;

Hello, we want to setup the following scenario: - each user has a softphone AND a hardphone - the softphone is started with the operating system - the hardphone is connected all the time using SIP - only ONE extension for each user Both phones should ring when the user is called. We've setup an asterisk 1.4.18 and at the moment only the last registered client rings. In Asterisk 1.2 the

hi i've got an AAstra 9133i ip phone, when i've bought it, i've set it to use a SIP/400 account on my asterisk, then, i've changed settings and i've set set phone to use a SIP/500 account . now, when i connect the phone to tthe network, it register itself on asterisk with both accounts!!! -- Registered SIP '500' at 192.168.100.188 port 5060 expires 120 --

Hi, In the early stages of deciding how to try and develop this environment, I looked at all the protocols that could be used. SIP was chosen just because it seemed to me that it was the most widely used protocol. I believe IAX is a new protocol with a little less documentation and examples. The good thing about this Jain-sip-phone is that it saves a lot of time since many of the important

I am trying to set up the BLF on a GXP2000. Currently what I have is extensions.conf: [globals] polycom430=SIP/101 [internal] exten => 101,1,Macro(voicemail,${polycom430}) [macro-voicemail] exten => s,1,Dial(${ARG1},10,tT) exten => s,2,VoiceMail(u${MACRO_EXTEN}@default ) exten => s,102,VoiceMail(b${MACRO_EXTEN}@default) [ext-local-custom] exten => 101,hint,${polycom430}

I running Asterisk 1.1 on Mandriva 2006. Everything works fine, can connect with softphone, send outgoing calls to VOIP provider. The only (and big) problem is that Asterisk refuses to authenticate incoming calls with the message (in the log): Failed to authenticate user "XXXXXXXXXX" <sip:XXXXXXXXXX@209.17.160.129> From what I've read in the various docs I could access, I

Hi all, I am working on asterisk 1.2.18 zaptel 1.2.17 Polycom 650 polycom 430 SIP version 2.0.3.0131 for IP 650 SIP version for IP430 2.0.3.0127 freepbx 2.2.1 I am trying to configure BLF using asterisk but failed. I would be thankfull if somebody help me. Regards FArooq ********************************************** 1 ********************************************** in my

Have asterisk@home 1.2.1 The server is on an internal network eg 10.10.10.10 It is NAT'd 1:1 via Checkpoint firewall to external public IP eg 50.50.50.50 The remote IAX2 phone (ATCOM320) is configured to call 50.50.50.50 on extension 1055. Outbound calls to 1055 work perfectly. Inbound calls from 1055 get picked up as if it were an external call (see below) and goes straight to the ring

Am having a unique problem, calls received on my SPA942 seem to end after 15 seconds, but calls made from this device do not have this problem. For this device (when receiving calls) I get periodic "chan_sip.c set_destination: can't find address for host" I have set the "canreinvite=no" in the sip.conf. Does anyone have a sample entry from sip.conf for the Lynksys SPA 942

I need to setup MWI on a few Aastra 9112's. I've tried doing so in the web interface by setting "Explicit MWI Subscription" to true, but no lights, no stutter tone. Firmware: 1.4.0.1048 Thanks! -- Warm Regards, Lee

Hello, I have the Jain-Sip-Applet-Phone installed on two machines in a small LAN network. These machines are connected through an Asterisk Server (Using Trixbox). I run the phone as an application on both machines through Eclipse and I am able to log on as a user with one of the extensions that I use within Asterisk on each machine (extensions 201 and 202 in this case). When I try to add a

Hi! Problem: I can't hear what the people at Location B i saying, they hear me but I do not hear them. They can call, I can call. Just no sound. My current setup is: Softphones/Hardphones(Location A) <-> Asterisk <-> Firewall/Nat <-> Internet <-> Firewall/Nat <-> Softphone/hardphone(Location B) I am having problems with sound, I have opened the

Hi there! I am having problems registering my 7970 hardphone with Asterisk 1.4(with FreePBX interface). I had an earlier post about trying to get it to work first with a 7970 emulator (Cisco IP Communicator) on the Asterisk Forum : http://forums.digium.com/viewtopic.php?t=19160 Instead I decided to try the real phone instead, and was able to advance further. The firmware was able to install

Hi, I have lookedaround and don't see this anywhere. Is there a way to tell the ip500 to not make the aural MWI blips?

Hi All, I have searched the various post and not able to find the solution. I am using Asterisk 1.4.21.2 for outgoing calls. Earlier i used ZAP trunk and it works fine. Now i need to move to SIP trunk and configured the same. When i try from softphone i got error as "Call rejected" and in the asterisk i got error as

Name/username Host Dyn Nat ACL Port Status 2011/2011 10.1.1.10 5071 UNREACHABLE 2010/2010 10.1.1.10 5070 UNREACHABLE 2009/2009 10.1.1.10 5069 UNREACHABLE 2008/2008 10.1.1.10 5068 UNREACHABLE 2007/2007

Longtime lurker, first time poster. :) A client of mine is in need of having Asterisk record every call that comes in from a specific incoming route. I've added the following lines to the sip_additional.conf file, but no recordings are showing up in the /var/spool/asterisk/monitor/ folder. record_out=always record_in=always Another page I came across on Google (

Hi all, I am trying to indentify a problem: I have 2 machines, one with Asterisk 1.0.11, the second with Asterisk 1.2.17. Both running with the same zaptel (1.2.16). Asterisk 1.0.11 running on Sarge with AMP's dialplan and the 1.2.17 running on Etch with FreePBX's dial plan. Now on both machines, I have some FXS connected (yes, I am talking about Astrinbanks...). The problem is that

Hi, I am upgrading a Cisco 7960 phone from SIP V.5.1 to 6.0 and then will to go up to 7.5 However in my first attempt to go from V.5.1 to 6.0 this is hat happens: - The phone reboots - The phone then reads the file OS79XX.TXT from the TFP server. In the file I added the version "P0S3-06-0-00" - It starts upgrading firmware - Then I get the following message: (Upgrade Failed -