similar to: 56k modem configuration

Hi, First i would like to thank the kind people of the list who have answered my previuos mail, but i am still stuck as asterisk still crashes upon startup, i have read the install article at http://www.voip-info.org/wiki-Asterisk+Step-by-step+Installation and i have search the asterisk archives, but i still cant get asterisk to work, i have tried reinstalling asterisk but it still complains and

I'm new to asterisk and fror a cupple of days I heave been googleing the net for digium "clones", because it's very hard for me to get a digium card (X100P). Does anyone Know another substitute for X100P (I know that intel based modem with chip 537/MD3200 is working but I did not find any of those) ? I made it work with an Intel 536 (with a costumised driver that I found on

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

Hello *, I have a strange problem with the MAPI proxy AstManProxy: sometimes it happens that I send a request and I receive a response to ANOTHER request that it got in the frame time between my request and my response. Did anyone else notice this behaviour? How can this be solved? I've been reading the source code, but I didn't find a solution. Thanks in advance, -- Dr. Andrea

Hello everybody, I'd like to have more detailed records for calls related to queues. For instance, if A enters in queue X, waits for Y secs and then talks to peer Z for T seconds, I'd like to have two entries in my CDR: - src: A, dst: X, duration: Y, state: ANSWERED - src: A, dst: Z, duration: T, state: ANSWERED This independently from how many peers the Queue app calls without success

When I try to connect to * using a Cisco ATA 188 configured with a MGPC firmware (v3.1.1), I just keep getting this message every 30 seconds or so : May 10 10:08:21 NOTICE[7913]: chan_mgcp.c:1509 find_subchannel: Gateway '192.168.1.27' (and thus its endpoint '*') does not exist Using tcpdump, I have checked that the ATA188 (with IP 192.168.1.27 and port 2427) sends UDP packets to

Folks, I've just successfully set up Asterisk (as part of the Asterisk Management Portal installation). When I say "successfully", I mean that I have gone through all the steps detailed for the installation of AMP and not hit any snags there. I can connect to my asterisk server via ssh and can also connect via Http to the portal to change settings in AMP. Now I'm trying to

Hi! I just installed Asterisk 0.4.0 with all the default options, and the configuration samples it has. When I try to dial from an h323 client (gnomemeeting) I get this message on the messages file: Jun 19 11:48:45 WARNING[15375]: File file.c, Line 410 (ast_openstream): File demo-congrats does not exist in any format Jun 19 11:48:45 WARNING[15375]: File file.c, Line 553 (ast_streamfile):

Hi I?m a new user and I do test with my hardware . I have a x100p and telephone vozip. And when I run this command asterisk ?vvvvc for to test it . My computer show it ?warning? [chan_iax.so] => (Inter Asterisk eXchange) == Manager registered action IAX1peers == Parsing '/etc/asterisk/iax1.conf': Not found (No such file or directory) Apr 2 07:45:12 ERROR[16384]:

Hi, I have upgraded my PBX to Asterisk 1.2.5 , previously I was using Asterisk 1.0.9, and Every thing was working fine ,But now voice mail is not working. The error I am receiving in log files is like following, WARNING[2413] app_voicemail.c: No entry in voicemail config file for '12' I have searched for solution a lot can Any one of you let me know how can I solve this issue

Hello all - This is my situation! I have a PC with no PCI slot and no modem! But I would like to install asterisk on it. I want to use SIP based software ONLY with the asterisk PBX system. I already have the asterisk running on a regular PC. BUt when I run assterisk it fails at this point when it parse modules.conf file. [Wait] == Registered application 'Wait' Asterisk Dynamic

Hi I tried to install the * in my Radhat 7.3 machine. The "gmake" and "gmake install" went fine, but "gmake sample" gave me errors of "configs/*.adsi", "sounds/demo-*" and "sounds/*.mp3" errors. I created a dummy.adsi in the configs folder and commented out the "sounds/demo-*" and "sounds/*.mp3" in the Makefile to

Hello *, do queues allow me to set an announce like the A() option of the Dial() cmd? The announce that I've found is a message that is heard by the caller. I'd like to send a message to the member of the queue that picks up the call. Thanks in advance, -- Dott. Andrea Spadaccini Multimedia Technologies Institute - MTI S.r.l.

Looking at the error I tried moving chan_modem* out of the modules folder and asterisk started and its working again... Not sure what changed in the chan_modem_i4l.so but removing it from the folder fixed my problem. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Eric Hall Sent: Sunday, January 23, 2005

Hello everybody, I'm aware that I can try to balance gain levels with PSTN cards using the ztmonitor tool, as described in http://www.asteriskdocs.org/modules/tinycontent/content/docbook/current/docs-html/x1695.html (Adjusting the rxgain/txgain Settings). Is there a similar tool for mISDN? If not, what is your approach to gain setting in mISDN? Thanks in advance, -- Dr. Andrea Spadaccini

Hello group I just update to the newest CVS now I'm not able to get asterisk to start. No error during the make or make install I did a make clean before the make;make install Any help would be great!!!! Here is the output asterisk -vvvvvgcd Parsing /etc/asterisk/asterisk.conf Parsing /etc/asterisk/extconfig.conf == Binding realtime_ext to mysql/realtime/extensions_table == Binding

Skipped content of type multipart/alternative-------------- next part -------------- [root@LINUXVM root]# asterisk -vvvc == Parsing '/etc/asterisk/asterisk.conf': Found Asterisk 0.4.0, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= == Parsing

Now that I have most everything actually working I've noticed that about every 3-4 days on average..... and at worse... Once a day my asterisk box seems to lose it's registered state with our sip provider and no longer will take any incoming calls. The caller simply hears a fast busy (reorder) If I do a reload at the command prompt all is well for another few days..... What I'm

Has anyone had any luck with PostgreSQL and Realtime? The realtime instructions on voip-info seem pretty straight forward... just not woking for me. I've included all of my config files below, and my console output. Entire console bootup output: [root@abox asterisk]# /usr/sbin/asterisk -vvvvvvc == Parsing '/etc/asterisk/asterisk.conf': Found == Parsing

Hi everyone, I am running asterisk on red hat linux 9 box. The sound card is Intel 82801db AC' 97 audio and the module is i810_audio. It runs well with other applications like xmms and the standard tests deliver a sound . I have also tried to record voice and that works well too. 1-)Now when i run asterisk and i dial out an extension to play any sound there is none. The same thing