similar to: Issue with calling queues

Update on this: I found that by changing insecure = very to insecure = invite, adding the second trunk no longer stopped calls working. I've read the documentation on this switch and still don't see how it applies/is meant to get used. Anyway, with this change in place, the following may help: asterisk*CLI> sip show registry Host Username

Hi, I am attempting to setup an asterisk server, current specs: CentOS release 5 (Final) Asterisk 1.4.11 Asterisk-gui checked out from SVN last week I started with a fairly basic setup involving one VOIP provider who provided one dial in number, and a couple of handsets. Config files are below. It was pretty much totally built by Asterisk-gui, except for the fact I had to add

Connected to Asterisk 1.4.11 currently running on asterisk (pid =3D = 31999) -- Remote UNIX connection Verbosity is at least 8 -- Executing [00425298582 at numberplan-custom-1:1] Macro("SIP/8001-b7d0bb20", "trunkdial|SIP/trunk_3/0425298582") in new stack -- Executing [s at macro-trunkdial:1] Dial("SIP/8001-b7d0bb20", "SIP/trunk_3/0425298582")

Connected to Asterisk 1.4.11 currently running on asterisk (pid =3D = 31999) -- Remote UNIX connection Verbosity is at least 8 -- Executing [00425298582 at numberplan-custom-1:1] Macro("SIP/8001-b7d0bb20", "trunkdial|SIP/trunk_3/0425298582") in new stack -- Executing [s at macro-trunkdial:1] Dial("SIP/8001-b7d0bb20", "SIP/trunk_3/0425298582")

Connected to Asterisk 1.4.11 currently running on asterisk (pid =3D = 31999) -- Remote UNIX connection Verbosity is at least 8 -- Executing [00425298582 at numberplan-custom-1:1] Macro("SIP/8001-b7d0bb20", "trunkdial|SIP/trunk_3/0425298582") in new stack -- Executing [s at macro-trunkdial:1] Dial("SIP/8001-b7d0bb20", "SIP/trunk_3/0425298582")

Connected to Asterisk 1.4.11 currently running on asterisk (pid =3D = 31999) -- Remote UNIX connection Verbosity is at least 8 -- Executing [00425298582 at numberplan-custom-1:1] Macro("SIP/8001-b7d0bb20", "trunkdial|SIP/trunk_3/0425298582") in new stack -- Executing [s at macro-trunkdial:1] Dial("SIP/8001-b7d0bb20", "SIP/trunk_3/0425298582")

Hey Everyone, Has any successfully installed this on a Toshiba A200? Any feedback would be great. Kind Regards Matthew Ollerenshaw Network Engineer * +612 1300 887 959 | Ê +612 9890 8349 | * mollerenshaw@visinet.com.au<mailto:mollerenshaw@visinet.com.au> | www.visinet.com.au<http://www.visinet.com.au/> Diploma (Network Engineering) | Microsoft Certified Professional ( MS

Dear The Expert, I am very new with this, I have installed AsteriskNow, X-Lite as my SoftPhone, I am using SPA-3102. I have 3 extensions, me at 250, 998 is my Linksys SPA-3102 and 999 for PSTN Line (see below) My problem is, I am unable to call 998, I thought this is registration problem, (because the Linksys screen info said Registration Failed) Could any body please help? Many thanks in

Dear all i'm creating an outgoing call to number xxx with this command: http://host:port/mxml?action=Originate&Channel=Local/xxx at to-external &Exten=testDTMF&Context=cRETEUNICA&Priority=1 wich points correctly to this portion of dialplan: [cRETEUNICA] exten => testDTMF,1,Answer exten => testDTMF,n,Read(digito,,1) exten => testDTMF,n,SayDigits(${digito}) The

Hello, everyone. Today I've installed an asterisk svn trunk (r61667). The problem I'm having is no matter what context I set in the config file for that peer, "default" is always being used. The output of "sip show peers" shows the context correctly, but when I try to make a call, using that peer, I can only dial the numbers set in the "default" context.

Hello, We have 2 SIP trunks from Bandwidth.com and if both are in use and someone tries to dial out, they cause another call to get one-way audio (the caller hears us, we cannot hear them). This happens 100% of the time and Bandwidth.com doesn't offer any support. I don't see any setting that tells Asterisk that there are 2 channels available from Bandwidth.com's IP. I'm

Hi! I run a mongrel cluster with 6 mongrels in it. I want to monitor them individually for process hangs (and then restart them) and this is the solution I came up with: Here''s my configuration file for monit (/usr/local/etc/monitrc): [snipped relevant bits] ------ #check lighttpd process check process lighttpd with pidfile /var/run/lighttpd.pid start program =

Hi list, I enabled the transfer function in my dialplan, but I may configure it wrong because sometime when I call a SIP extension number from one FXS port, the SIP side will hear word "transfer", I hear nothing, after that, the call conversation is fine.I'v had this problem for a long time, could not get clue where I configure it wrong. here is my related config part: sip.conf:

I'm in the process of testing a TLS/SRTP install. My experience is improving with each new challenge, but this one is a great test of my 2 month experience with Asterisk. When I dial 6003 from 6001, it takes 35 seconds until I get the error message that 6003 is circuit-busy. Any help would greatly be appreciated. Below is the error message and the extensions and sip.conf files. *CLI>

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi! Are hints not yet implemented in res_jabber? I have this here: exten => 3000,hint,gtalk/gtalk_account/mari.xxxxxxx at gmail.com But the hint doesn't show any difference. It always shows online on the phone and core show hints always shows that: 6003 at internal : SCCP/6003 State:Unavailable Watchers 0 6002 at internal :

Hi, I am trying to setup a simple home voip service w/ * I have compiled and installed the svn source as a first step I am trying to configure SIP for inside my network. I have a handful of softphones and a few hardphones that I want to all be able to call each other I have configured users.conf with a single softphone(kphone) and have tried calling itself (ext 6000) and the demo from the

Hello, I'd like to be able to see if a channel is use and handle the call differently if it is. The best I can find is the command ChanIsAvail(). The problem is, I have an snom200 phone which does call waiting, so even if it is engaged in a call, a second channel is still available on it. I would like to be able to differentiate between these two cases: no calls engages, or calls

I have a SIP phone calling via a SIP trunk another asterisk system, that then sends the call out a ZAP channel. When I press any of the features defined in features.conf, The end user on the ZAP side hears the DTMF tones, and none of the features work. My DTMFmode on the SIP users definition is rfc2833 Asterisk console doesn't register that a feature is being recognized, any ideas? Below

Hello everyone, I have previously asked this question on the asterisk-video list, but I got directed here. I have a setup consisting of asterisknow beta4 (not sure if that is crucial) and a few clients all running X-Lite 3.0 (not eyebeam) on the local network. My computer has a USB-Camera installed, and now I would like to do some video calling with it, at least, so that the other user can

i am configured asterisk-gui the "Queue Extension Configuration" but configure and register into queue.conf : [66666] fullname = Call Center strategy = ringall timeout = 5 wrapuptime = 5 autofill = yes autopause = no maxlen = 0 joinempty = no leavewhenempty = no reportholdtime = yes musicclass = default member => Agent/60010 member => Agent/60011 member => Agent/60014 but not