Displaying 20 results from an estimated 2000 matches similar to: "Setting Callerid with chan_misdn"
2007 Jun 06
3
Asterisk call quality detection
Hi Chaps,
Is there a way to detect/highlight poor quality voice
calls going through an asterisk server?
Was thinking of picking up a cdr record or some other
variable showing poor quality on calls when the
internet is having issues.
Is there any qos or poor audio quality variables
available?
Cheers,
Taff.
___________________________________________________________
Yahoo! Answers - Got
2005 Mar 08
0
problem in compiling chan_mISDN
Hi List, I?m having problems compiling chan_misdn:
asterisk:/usr/src/chan_misdn-beta-0.0.3-rc4 # make install
cc -ggdb -Wall -D_GNU_SOURCE -Wno-missing-prototypes
-Wno-missing-declarations -fPIC -I/usr/src/asterisk/include
-DAST_CONFIG_DIR=\"/etc/asterisk/\" -I/usr/src/mISDNuser/include
-I/usr/src/linux-2.6/include -I/usr/src/mISDNuser/i4lnet/ -Wall -c -o
chan_misdn.o chan_misdn.c
2007 Jul 27
1
chan_mISDN module does not load
Hi,
I have a Digium B410P 4-port BRI card.
I installed misdn 1.1.3 with hfcmulti driver and
misdnuser 1.1.3.
I configured the card "correctly" as misdnportinfo
reports:
# misdnportinfo
Port 1: TE-mode BRI S/T interface line (for phone
lines)
-> Interface is Poin-To-Point.
-> Protocol: DSS1 (Euro ISDN)
-> childcnt: 2
--------
Port 2: TE-mode BRI S/T interface line (for
2005 Aug 15
2
asterisk + chan_mISDN = undefined symbol: ast_pickup_call
Hi all!
I'm getting an error when I try to start asterisk with chan_misdn.
I patched my kernel (2.6.12.4), and compiled the whole stuff (kernel,
mISDNuser, asterisk, chan_misdn). I got mISDN from
http://isdn.jolly.de/download/v3.0/
I'm using a CVS Snapshot of asterisk, which was checked out about 5
hours ago.
This is the error:
[chan_misdn.so]Aug 15 14:13:29 WARNING[4929]:
2005 Jan 21
1
chan_misdn 0.0.3-rc5 - new release ! Please testit.
What are the advantages in using mISDN over other solutions?
If I knew why it was a good idea (like does it have better sound quality than alternatives?) then I would put the time in to test it, and also improve the Wiki.
-----Original Message-----
From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Thomas H?ger
Sent: Friday, January 21,
2005 May 12
1
chan_capi and chan_misdn
Could someone please comment on the current state of chan_capi,
chan_misdn and chan_modem channel drivers in terms of functionality and
stability. Specifically, which channel driver would be best for a
passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that
chan_capi distinguishes between junghanns and non-junghans cards, and
that chan_misdn is better suited for general misdn
2005 Jan 12
0
chan_misdn - new release ! Please test it.
Hi there,
we've announced a new release of our chan_misdn channel driver.
chan_misdn is a GPL channel driver for the new Linux ISDN-Layer mISDN
(www.isdn4linux.org).
So you can use all from mISDN supported ISDN catds in Asterisk.
Feel free to donwload and test it at :
http://www.beronet.com/download/chan_misdn-beta-0.0.3-rc4.tgz
You can report bugs and feature requests to
2005 Jan 21
0
chan_misdn 0.0.3-rc5 - new release ! Please test it.
Hi there,
we've announced a new release of our chan_misdn channel driver.
chan_misdn is a GPL channel driver for the new Linux ISDN-Layer mISDN
(www.isdn4linux.org).
So you can use all from mISDN supported ISDN catds in Asterisk.
Feel free to donwload and test it at :
http://www.beronet.com/download/chan_misdn-beta-0.0.3-rc5.tgz
You can report bugs and feature requests to
2005 May 16
0
chan_misdn and passive BRI cards
Has anyone got chan_misdn working with passive BRI cards yet? I've tried
both hfc (hfcpci.ko) and w6692 (w6692pci.ko) cards, but when I start
asterisk I get the following when chan_misdn is loaded:
[chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri))
== Parsing '/etc/asterisk/misdn.conf': Found
== Registered channel type 'mISDN' (This driver enables the
2005 Jun 06
2
mISDN + chan_misdn.so + winbond issue
Hi all,
Does anybody of you have the winbond w6692 working with the
mISDN/chan_misdn.so?
When loading chan_misdn.so from Asterisk, I get a "No lower Id port:1"
error. The /var/log/messages file says: "MISDN free_device: entitylist
not empty"
I'm using Linux 2.6.11.11 + mISDN-CVS-2005-05-01 + Asterisk 1.0.7 + Zaptel 1.0.7
chan_misdn build from chan_misdn-beta-0.0.3-rc6
2006 May 12
3
Echo cancel: chan_misdn vs bristuff? HFC card vs expensive card?
Hello everyone.
I've got a HFC ISDN card that I'm using with chan_misdn and it basically
behaves like crap. Echo is waaay worst then echo I get TDM400 card,
sound is "choppy" (there other side is allays complaining about sound
interruptions) and to top it all it detects fake DTMF's all the time.
Is this a chan_misdn problem or is it a card problem? I really need to
get
2004 Dec 04
1
chan_misdn and Dynalink IS64PH ISDN
Hi
For use my isdn card in NT mode I have compiled
chan_misdn.
When I launch asterisk it stop with th e message :
[chan_misdn.so] => (Channel driver for mISDN Support
(Bri/Pri))
== Parsing '/etc/asterisk/misdn.conf': Found
UnLocking config_mutex
== Registered channel type 'mISDN' (This driver
enables the asterisk to use hardware which is
supported by the new )
Locking
2005 Feb 18
0
More on W6692pci NT mode under chan_misdn
So far i've grasped that to use a card in NT mode it should have
layermask=3 as module option. Is it the only thing that sets TE or NT
mode for card? Perhaps there are settings in misdn.conf ? I can only
get the card to work in TE mode and even then when asterisk is ran as
asterisk -vvvgc it exits right after chan_misdn is loaded with theese
messages:
[chan_misdn.so] => (Channel driver
2005 May 12
5
chan_capi, chan_misdn and chan_modem
Could someone please comment on the current state of chan_capi,
chan_misdn and chan_modem channel drivers in terms of functionality and
stability. Specifically, which channel driver would be best for a
passive PCI HFC or W6692 ISDN card. The chan_misdn wiki claims that
chan_capi distinguishes between junghanns and non-junghans cards, and
that chan_misdn is better suited for general misdn
2005 Jul 25
4
Fritz PCI card in ptp mode with chan_misdn
Hello !
I would like to get working a Fritz PCI card using chan_misdn
operating in ptp mode.
Afer compiling mISDN into the kernel and building chan_misdn
Asterisk stops loading with :
[chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri))
== Parsing '/etc/asterisk/misdn.conf': Found
UnLocking config_mutex
== Registered channel type 'mISDN' (This driver enables
2006 Apr 25
2
Help on chan_misdn and MSN's
Quick question:
Is there a way to distinguish between calling MSN's when using chan_misdn?
More info:
I've got my ISDN2 (EuroISDN) up and running here in Romania with 1 base
number plus 5 MSN's. Now I want to my * to do different things when
receiving a call on from different MSN's (like forwarding the call to my FAX
machine or forwarding the call to my mobile).
The obvious way
2007 Feb 14
1
Asterisk 1.4 and chan_misdn
Hi list,
I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from
SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in
zaptel dir and: make, make install, make b410p. Everything is ok. Now I
want to compile Asterisk but can't activate the chan_misdn channel which
depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E)
When I made the make b410p, all
2007 Apr 11
0
Re: nadi: branch 1.4 r61342 - /branches/1.4/channels/chan_misdn.c
Author: nadi
Date: Wed Apr 11 05:52:28 2007
New Revision: 61342
URL: http://svn.digium.com/view/asterisk?view=rev&rev=61342
Log:
AOCD's are now exported to asterisk channel variables.
Modified:
branches/1.4/channels/chan_misdn.c
This is very cool, something i've waited for a long time :-). Is there a way
to write this into CDR or sendtext() it to a channel?
Regards,
Andreas
2004 Jul 05
0
chan_misdn HFC-NT dialtone
How is it possible to get a dialtone using chan_misdn for a ISDN
phone connected to a hfc nt-mode card?
misdn.conf:
[intern]
ports=2
context=isdnIntern
immediate=yes
extensions.conf
[isdnIntern]
exten => s,1,DigitTimeout(5)
I don't want to use answer here because the phone does not show the
dialed digits in the display if the call has already been answered.
--
Stefan Tichy
2005 Jan 22
0
Fwd: Re: chan_misdn 0.0.3-rc5 - new release ! Please test it.
Thomas H?ger wrote:
> So you can use all from mISDN supported ISDN catds in Asterisk.
>
> Feel free to donwload and test it at :
> http://www.beronet.com/download/chan_misdn-beta-0.0.3-rc5.tgz
>
> You can report bugs and feature requests to www.beronet.com/bugs
>
> Have fun!
Hi,
I have a few questions I've a lot of troubles with i4l.
Among others:
- very big latency