similar to: libmfcr2 is giving compilation errors

Hi, downloaded the latest snapshot just right now at soft-switch for MFC/R2 support and I get this message when trying to do libmfcr2; any idea ? it looks like he's not reaching Unicall. Thanks, Fred # make make all-am make[1]: Entering directory `/usr/src/libmfcr2-0.0.3' if /bin/sh ./libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -I. -I. -I/usr/include/libxml2 -g -O2 -MT

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I downloaded and installed the files in the follwing sequence spandsp libsupertone libunicall Till here it is compiling and

Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of

hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I downloaded and installed the files in the follwing sequence spandsp libsupertone libunicall Till here it is compiling and copying

Hi list: I want to modify the libmfcr2. But i can't find where is define the end DNIS signal is define. Actually the libmfcr2 send a ONE (1) at the end of sending all the DNIS numbers. I need to send a TWO (2), this becouse in Mexico the normal is to send a 2 at the end, not a ONE. In the next example i dialed un 6 19:12:17 WARNING[719] chan_unicall.c: MFC/R2 UniCall/5 Call control(1)

Hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I

Hi Asterisk-user, Steve; I?m using "*libmfcr2-0.0.3.tar.gz, libsupertone-0.0.2.tar.gz, libunicall-0.0.3.tar.gz,spandsp-0.0.3pre22.tgz*" with Fedora core 6 ,Asterisk 1.2.14, libpri 1.2.4 , zaptel 1.2.20; So everything is working perfectly with MFCR2, but sometimes i have problems with MultiFrame Alignment Signal (MFAS),i?m using standard G.732..I would like to Know, where can i

I don?t know if the last message was with content. So, I sent again. I have installed a Digium card TE210P and unicall for use MFC/R2. I think that it?s all right but I can?t make and receive calls. I?m using asterisk 2.1 with the patch made by Jos? P. Leit?o and the follow libs: libsupertone-0.0.2 libunicall-0.0.3 libmfcr2-0.0.3 zaptel 2.1 My number is 34318300. The Telco send me only 8300.

---------- Forwarded message ---------- From: Brian Hutchinson <b.hutchman at gmail.com> Date: Fri, 11 Jan 2008 12:22:09 -0500 Subject: Trying to build MFC/R2 Hi Moy, I downloaded your astunical-1.4.16 and have been studying it. I have a machine running the latest download of asterisk-1.4-17 and was trying to figure out how to build MFC/R2 support into it. I merged your unicall specific

Hello there! I've problem with setting up unicall / mfcR2. can't find proper notation for channel, trying unicall/1, unicall/1/1001, unicall/g1, unicall/g1/1000 and still having no luck. klaudia*CLI> !cp call /var/spool/asterisk/outgoing -- Attempting call on Unicall/1001 for application Dial(363) (Retry 1) Mar 25 09:29:34 NOTICE[19920]: channel.c:2429 __ast_request_and_dial:

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com>

Hi Moy, Bottom line up front (yes I'm military):How do I now configure some of my spans as normal Euro ISDN and a few with R2? Do I use a combination of /etc/asterisk/unicall.conf and /etc/zaptel.conf or just unicall.conf for everything? See below for the rest of the details and thanks in advance for advice! I downloaded your astunical-1.4.16 and have been studying it. I have a machine

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2

---------- Forwarded message ---------- From: Juan Carlos Huerta <juancarloshuerta at gmail.com> Date: 07-abr-2009 13:41 Subject: Re: [asterisk-r2] MFCR2 With Unicall - can unicall affect zaptel commands? To: asterisk-r2 at lists.digium.com Please wirte to asterisk-users at lists.digium.com to get help about this problem. Juan Carlos ~ Lo que no te mata te fortalece ~ On Tue, Apr 7,

If I make a call to asterisk's r2 E1 I get these errors *CLI> Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x1 [1/ 1/ 0/ 0] Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Detected Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Making a new call with CRN

Is there any way to compile Unicall's libraries (mfcr2, spandsp, chan_unicall, etc) for Asterisk 1.4? BarZ

Hi All I have problem with LIBMFCR2 for once Exchange I using Sangoma card, the firstly. my ssystem run successful with MFCR2, connected to E10 (Acatel Exchange), after that, i move connection connect to EWSD (Siemens), my system don't work. error protocol R2. my system: Asterisk CVS 1.1.X LibMFCR2 pre.005 and unicall-pre.005 this's my setting and my setting wanpipe1.conf

Hello, i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package: libpri-1.4.2 asterisk-1.4.9 spandsp-0.0.4 unicall-0.0.5pre1 libmfcr2-0.0.3 libsupertone-0.0.2 libunicall-0.0.3 zaptel-1.4.4 i'm using a E1 pci card with R2 but they not work, when I start the asterisk its generate this log: [May 12 08:53:24] WARNING[30814] channel.c: No channel type

Hi, I am trying to configure for MFC/R2 for asterisk. With the help of one of the asterisk users group member patrick I am able to install libunicall library. Now, when trying to install libmfr2-0.0.3 it is giving error. On running running command $./configure It is giving error -> can't build without libtiff I downloaded tiff-3.8.2 and installed the libraries but still