similar to: TE120P digium card PRI_CPE error

Dear all I have now install TE210P 2 port E1 card on asterisk 1.4.10 on centOS 5 but thing is that i have connect 1 E1 port with avaya E1 back 2 back and second E1 card on Direct Telcom for outgoing for outside now i got this error when i call on avaya PRI asterisk think PRI_CPE and remote end also CPE i have configure /etc/zaptel.conf span=1,1,0,ccs,hdb3

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

I am wanting to front-end a legacy PBX with an asterisk box. I have done plenty of asterisk work over the last 6 months to PRI circuits, but not with a PBX being involved. I know I can use asterisk and digium cards in this manner, but do I need separate cards for the PRI -> Asterisk side to the Asterisk -> PBX side, or will a 4-port PRI card do the job? (I already have a spare one of

Hi, I am facing problem in configuring D-channel. I did the following configuration for TE-120P card /etc/zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 /etc/asterisk/zaptel.conf group=1 signalling=pri_cpe switchtype=euroisdn context=incoming channel=1-15,17-31 DIGIUM card is connected through cable to another end.On placing call from other end to

Hi, at the moment we have in Avaya Integral PBX with german pri (30 lines). We want to smouthly migrate to an Asterisk server. For this reason: Is it possible to route the external german pri (E1) through Asterisk server to that Avaya PBX? I think at first we need a Digium e1 card 4-Port. But how do we have to configure the routing of the whole PRI? I really would appreciate any sample

We have been working a OpenSer/Asterisk solution to replace our Avaya PBXs.The OpenSer is to provide scalability and the Asterisk to provide rich features.I know this has been many times for calling card platforms but I'm not sure if anyone has a good scalable solution they are using on their virtual PBX or in a CPE PBX environment?If so I would like to talk to them about buy their deploying,

I'm trying to make H.323 trunk between AVAYA&Asterisk. But call from AVAYA is terminated inmediatelly when apps DIAL on Asterisk is started. Does any one use AVAYA and h.323 channel? Thanks Bob.

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

Hi, I have successfully configured DIGIUM card and successfully communicated through it to the another E1 card running application. Can anybody tell me does TE120P support MFC/R2 protocol. Thanks and Regards sanchal singh

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

The Telco in Canada is been real painful. I was wondering if anyone has installed a Digium TE1X0P card in Canada and if their Telco was so difficult. The Telco will not provide us a service until they see a FCC or DOC number for the equipment ware are connecting to their service. If have found "FCC Part 68, ANSI/ITA-968-A, Including Amendment A1 and A2 Industry Canada CS-03"

I'm trying to upgrade from 1.4.24.1 to 1.6.0.9 with a TE120P card. I can't make any connection over the T1. From CLI: ERROR[26017]: chan_dahdi.c:14300 process_dahdi: Unknown signalling method 'pri_cpe' at line 37. cat chan_dahdi.conf cat chan_dahdi.conf [trunkgroups] [channels] language=en ;internationalprefix = 00 ;nationalprefix = 0 context=from-pstn switchtype=national

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

I have a brand new TE120P card that I have installed and asterisk is not starting as I am getting the error: ERROR[5054] chan_zap.c: Unknown signalling method 'pri_cpe' It seems it does not matter what I change the vaule for signalling= to, it always returns it as invalid. I have tried the config from my other 2 servers running TE110P cards and the config from AusTechPartniships

Just upgraded to most recent CVS and now I get this: pri_dchannel: PRI Error: We think we're the CPE, but they think they're the CPE too. when starting asterisk. Needless to say, I can't run asterisk without my PRI. Guess I'll start reverting code backwards day by day until I find the code that works. -Matthew

Hello List, We purchased a TE120P card from Digium and it works great. The only problem is that we are still experiencing echo on some calls. I've tried various echo cancellers (right now we are using OSLEC) and still no luck. My question has anyone gone from the TE120P to a Sangoma A101D-X Single Port T1/E1/J1 w/ echo cancellation? Have you noticed a difference? Also I called

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]

Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).

Hi, I am facing problem in configuring D-channel for TE120P card.I did the following things /etc/zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 /etc/asterisk/zaptel.conf group=1 signalling=pri_cpe