similar to: Saftware RAID1 or Hardware RAID1 with Asterisk

> > Dear all, Thanks for the greate explanation regaing Software/H/W Raid. This details better but on voip-info.org/wiki pages. Thanks lot agian. Regs, Vidura Senadeera. ====================================== Dear All, > > > > I would like to get community's feedback with regard to RAID1 ( Software > or > > Hardware) implementations with asterisk. > >

Dear Andrew, Thanks for your kind responce. Regards, vidura. ============================= > Motherboard with SATA RAID1 support That's a mulit-port SATA controller with RAID in the driver (software). > 256 MB RAM Use a little more RAM. > digium PRI/E1 card Is there any reason you aren't using Sangoma cards? > 1. If I use Software RAID, what would be the impact to my

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

Hellow, * I have a problem with dial up signalling. currently I have configured asterisk server and E1 card to ISP. then other side I am having ATA to PC for connecting internet through DialUP connection. is it possible and please send me the procedure how I can do it ?? * ISP< <-> Asterisk <-> ATA <-> DIALUP -- Thanks & Regards, Vidura Senadeera, Sri Lanka.

Hi All, I would like to explain the layout that i am trying to achive. I am so helpless on this regard. So here is the story ........ " This is with regard to the setup which you can find at the "Asterisk The Future of Telephony" , chapter 11, page # 196-197, I am attaching the picture for your information. Now I am taking a challenging step to of integrate IP PBX with our

> > Hi, You can achieve this by integrate CCM and asterisk using SIP trunk. In CCM you can create SIP trunk, After creating SIP trunk in between CCM and asterisk, you have to configure dialplan on CCM to pass the calls to asterisk. One the caller id comes to Asterisk you have to use extension.conf to route the calls. You can also try with freepbx GUI to configure inbound route, it makes

Dear All, I am experiance a issue with my IAX clients. I have upgradeed Asterisk to 1.4.28 After then IAX clients are not working and It's not registering even. Please help. Asterisk previous version - 1.4.26.1 ( for this worked fine) FreePBX version - freepbx-2.5.2 -- Thanks & Regards, Vidura Senadeera, Sri Lanka. msn/yahoo/skype Ids - vidurased -------------- next part

Hi Carlos/All, Thanks for your reply. I can remove dchan=16 from zaptel.conf But according to the documentation of Digium and sangoma they mentioning to use dchan=16. Are there any specific reason you have experiance regarding this and I am confusing that what this is included to the documentations. Regards, Vidura. On Wed, 2007-09-05 at 20:26 +0530, Vidura Senadeera wrote: > Dear All,

> > > Hi, > > > I checked by changing to from-zaptel, but no luck yet. Pls guide me on > this. > > Regards, > vudura senadeera > > > ------------------------------ > > > > Message: 9 > > Date: Fri, 19 Jan 2007 16:47:18 -0000 > > From: "Robert Jenkins" < raj@jrw.co.uk> > > Subject: RE: [asterisk-users]

Deat all, I am in middle of integrate Asterisk with Toshiba astrata legacy pbx. Following is my setup *Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX* A =============================================> B C <============================================ D Asterisk PBX and strata PBX connected using back to back E1 cross cable. Physicall connectivity

Hi all, I?m trying to create a RAID1 on a machine. I?ve already configurated BIOS (mother board, Intel, S500VSA SATA) so as to build RAID1 via hardware. However on CentOS Installer, when I reach "disk setup" screen, it shows up 2 devices (/dev/sda and /dev/sdb). Is this right (both devices being showed)? How should I proceed on this moment? If I create the

I have a 750Gb 3-member software raid1 where 2 partitions are always present and the third is regularly rotated and re-synced (SATA disks in hot-swap bays). The timing of the resync seems to be extremely variable recently, taking anywhere from 3 to 10 hours even if the partition is unmounted and the drives aren't doing anything else and regardless of what I echo into

I'm seeing a problem that I think maybe a bug with the mdraid software on the latest CentOS installer. I have a couple of new supermicro servers and each system has two innodisk 32GB SATADOM's that are experiencing the same issue. I used the latest CentOS-7-x86_64-1611 to install to the two SATADOM's a simple RAID1 for the root. The install goes just fine but when I boot off the new

Hello, Having a problem with software RAID that is driving me crazy. Here's the details: 1. CentOS 6.2 x86_64 install from the minimal iso (via pxeboot). 2. Reasonably good PC hardware (i.e. not budget, but not server grade either) with a pair of 1TB Western Digital SATA3 Drives. 3. Drives are plugged into the SATA3 ports on the mainboard (both drives and cables say they can do 6Gb/s). 4.

Hi, I have two 320 GB SATA disks (/dev/sda, /dev/sdb) in a server running CentOS release 5. They both have three partitions setup as RAID1 using md (boot, swap, and an LVM data partition). # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdb1[1] sda1[0] 104320 blocks [2/2] [UU] md1 : active raid1 sdb2[1] sda2[0] 4192896 blocks [2/2] [UU] md2 : active raid1 sdb3[1]

With Centos3, fedora1/2 I have been able to put /boot on a RAID1 partition and have it boot normally. Unlike earlier versions that used lilo as the default boot loader, these did not make the 2nd drive bootable but at least I was fairly confident that if the first drive failed I could use the install CD in rescue mode to fix up the 2nd one and go on. However, Centos4 won't boot at all with

Hi All, Thanks for every one who helped me on this regard. I think i was able to rictify the problem. what i did is remove callprogress=yes usecallinpres=yes and restart asterisk. Today i didn't report any drop calls. Many thanks for Eric. :) I hope this situation will continue. Regards, Vidura. On 3/8/07, Vidura Senadeera <vidurased@gmail.com> wrote: > > Hi, > >

Is there anything special that anyone here has had to do to get an Aastra phone (on the Internet) to talk to Asterisk behind a PIX firewall? Ports 10000-20000 UDP are open on the PIX and forwarding to the Asterisk server. The Asterisk server's RTP.CONF is set to use 10000-20000. The phone registers, and will place AND receive calls, however, no audio is passed. The phone is an Aastra

Hi, I''m starting to play with btrfs on my new computer. I''m running Gentoo and have compiled the 2.6.31 kernel, enabling btrfs. Now I have 2 partitions (on 2 different sata disks) that are free for me to play with, each about 375 gb in size. I wanted to create a "raid1" volume using these two partitions, so I did: # mkfs.btrfs -d raid1 /dev/sda5 /dev/sdb5 # mount

Hi, I'm currently experimenting with software RAID1 on a spare PC with two 40 GB hard disks. Normally, on a desktop PC with only one hard disk, I have a very simple partitioning scheme like this : /dev/hda1 80 MB /boot ext2 /dev/hda2 1 GB swap /dev/hda3 39 GB / ext3 Here's what I'd like to do. Partition a second hard disk (say, /dev/hdb) with three