similar to: Asterisk 1.2 TDM24xx and B410P

We have an Ubuntu Dapper with 2.6.14 kernel, asterisk 1.2.14 debs from http://pkg-voip.buildserver.net When misdn stuff (misdn-init start) is not started, everything is fine, our 8 FXO (Channel 1-8) 4 FXS (21-24) are working well. If we start the misdn stuff (one card, port 1,2,3,4 in misdn-init.conf and no TELCO cable plugged in the card), the dialtone disappear on TDM lines :-( Does

Hi, My setup is: IPPhone1 --- Asterisk1 with B410P ---- Patton 4638 --- Asterisk2 --- IPPhone2 I want to evaluate Asterisk1 in TE/PtmP mode. So, Patton box is configured in NT/PtmP (with 3 BRI links between both systems). Anyway, asterisk -rx "pri show spans" keeps replying : PRI span 1/0: Provisioned, Down, Active PRI span 2/0: Provisioned, Down, Active PRI span 3/0: Provisioned,

Hi. I have installed B410P in Europe and the cards works more or less ok. My question is what color should the LED's on the back of the card be when connected to the PSTN NT box? Is there anywhere some information on the expected LED color in any given state (idle, call active, cord unplugged etc.)? On my card the lights are shining Red(orange-ish) but flashing to green every now and

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden

With pleasure we announce the release of tinc version 1.1pre10. Here is a summary of the changes: * Added a benchmark tool (sptps_speed) for the new protocol. * Fixed a crash when using Name = $HOST while $HOST is not set. * Use AES-256-GCM for the new protocol. * Updated support for Solaris. * Allow running tincd without a private ECDSA key present when ExperimentalProtocol is not

With pleasure we announce the release of tinc version 1.1pre10. Here is a summary of the changes: * Added a benchmark tool (sptps_speed) for the new protocol. * Fixed a crash when using Name = $HOST while $HOST is not set. * Use AES-256-GCM for the new protocol. * Updated support for Solaris. * Allow running tincd without a private ECDSA key present when ExperimentalProtocol is not

Hi, My set up is : Asterisk with B410P in NT mode <-------------cat5 straight cable ----------------> Another PBX in TE mode Is the 100 Ohm terminator you can find on B410P boards, necessary when connecting in NT mode to another PBX (set in TE mode) ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations

We have recently purchased a B410P Digium 4* ISDN-2 card with hardware EC. On the same server, I also have a regular Digium 4-channel PSTN-card (TDM410P ?), used to interface to some analog devices, a.o. 2 fax machines. For faxing, EC needs to be off (or so I understand from the archives). How can I switch EC off for an ISDN B-channel if a fax is coming in? Z.

Hello, Junghanns and BeroNet offer 8 BRI ports cards. Do you know if Digium's B410P has an inner TDM bus so that an 8 BRI ports subsystem (2 PCI slots used, but 1 one set of interrupts) could be made out of 2 B410P ? I know you could (theorically) do this with Junghanns and BeroNet cards. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I've read that the new dahdi channel supporting B410P doesn't support PtmP when in NT mode. Does it support PtmP when in TE mode ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm

Hi all! Sorry for my poor english, i'm italian. I installed Digium B410P on my asterisk server. I followed the official installation instructions found on digium site. These instruction, in my opinion, are not clear, so i tried with other ways (found on the trixbox site). I found this: http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p Now i can receive

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf:

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hi, Which echo-canceler shall I pick for Digium B410P ? Is HPEC relevant ? Reading from its datasheet, it seems related to analog cards. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080221/ed5c5d6f/attachment.htm

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

I have the same problem as the following: http://threebit.net/mail-archive/asterisk-users/msg36602.html I am using a b410p (Wildcard) in TE mode on 4 channels of ISDN2e and it totally fails to detect incoming DTMF. The newer mISDN drivers have a parameter "dtmfthreshold" where you can tune the volume above which DTMF detection is initiated. However (I've tried it) the newest

We own an Asterisk box with the following configuration: Linux Debian 4.0 Kernel 2.6.18 Asterisk 1.2.23 Zaptel 1.2.19 We installed a Digium B410P card, and we are using 3 ports in te_ptp mode (it is connected to BRI adapters on Italian ISDN lines, provided by Telecom Italia; in Cisco language, they should be "isdn switch-type basic-net3"). Configuration strictly complies the

Hi, I've setup a trixbox 1.2.2 instalation with digium b410p. It uses misdn driver. I'm able to place calls and receive calls using this interface. One thing that happens is when i dial an a number from a sip client to an number that is routed through b410p and the called party rejects the call, asterisk doesn't detect the hangup. The sip client remains in ringing waiting for the