Displaying 20 results from an estimated 1000 matches similar to: "Which spandsp & unicall version to use with 1.2?"
2005 Jan 10
10
Unicall errors
If I make a call to asterisk's r2 E1 I get these errors
*CLI> Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x1 [1/ 1/ 0/ 0]
Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Detected
Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Making a new call with CRN
2007 Dec 11
2
Unicall protocol error. Cause 32776
Dears,
After having set up the board Digium TE420 to receive 3 E1s, I can receive
calls without difficulties. As you can see in the log below:
-- Executing [5908 at from-pstn:1] NoOp("UniCall/14-1", "Catch-All DID Match
- Found 5908 - You probably want a DID for this.") in new stack
-- Executing [5908 at from-pstn:2] Goto("UniCall/14-1",
2006 Apr 03
4
R2 protocol error
Hi,
I have three R2 installation on different carriers, all shows the same inconsistency at varying
degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier
claims that it's my R2 box that is not responding in time. Please, check the attached file and
take note of the timestamp, you'll find that in some call, it already contradict what the carrier
2010 May 12
1
problems with unicall
Hello,
i'm using asterisk 1.4.9 in fedora 7, i was compiled its with this package:
libpri-1.4.2
asterisk-1.4.9
spandsp-0.0.4
unicall-0.0.5pre1
libmfcr2-0.0.3
libsupertone-0.0.2
libunicall-0.0.3
zaptel-1.4.4
i'm using a E1 pci card with R2 but they not work, when I start the asterisk
its generate this log:
[May 12 08:53:24] WARNING[30814] channel.c: No channel type
2008 Apr 01
1
Unicall + incomplete DNIS on international calls
Hello everybody, i'm from Mexico, at the time i?m working on a production
server with asterisk 1.2.25 + spandsp-0.0.4 +
libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I
installed this version of astunicall that i downloaded from
http://www.moythreads.com/astunicall/
Everything works fine, i'm able to make outgoing calls and recive incoming
calls with all ANI and
2008 Feb 01
1
Unicall
Hello All, we have Asterisk 1.4.9, Unicall 1.4.9-0.1, and Zaptel
1.4.5.1. If we were to update or recompile Asterisk, would we need to
do anything with Unicall or Zaptel?
Thanks in advance
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080201/b80fa496/attachment.htm
2008 Jan 11
1
Fwd: Trying to build MFC/R2
---------- Forwarded message ----------
From: Brian Hutchinson <b.hutchman at gmail.com>
Date: Fri, 11 Jan 2008 12:22:09 -0500
Subject: Trying to build MFC/R2
Hi Moy,
I downloaded your astunical-1.4.16 and have been studying it.
I have a machine running the latest download of asterisk-1.4-17 and was
trying to figure out how to build MFC/R2 support into it.
I merged your unicall specific
2008 Jan 12
1
MFC/R2 Signaling configuration
Hi Moy,
Bottom line up front (yes I'm military):How do I now configure some of my
spans as normal Euro ISDN and a few with R2? Do I use a combination of
/etc/asterisk/unicall.conf and /etc/zaptel.conf or just unicall.conf for
everything?
See below for the rest of the details and thanks in advance for advice!
I downloaded your astunical-1.4.16 and have been studying it.
I have a machine
2007 Aug 24
1
Error in loading libunicall.so module while running asterisk command
On 8/23/07, sanchal.singh at alliance-infotech.com
Hi,
I am using debian 4.0 with version 2.6.18-4-686
I have downloaded the required files form site
asterisk-1.2.24.tar.gz
libmfcr2-0.0.3-1.4.tar.bz2
libsupertone-0.0.2.tar.gz
libunicall-0.0.3-1.4.tar.bz2
2007 Aug 23
1
unable to load chan_unicall.so
Hi,
I am using debian 4.0 with version 2.6.18-4-686
I have downloaded the required files form site
asterisk-1.2.24.tar.gz
libmfcr2-0.0.3-1.4.tar.bz2
libsupertone-0.0.2.tar.gz
libunicall-0.0.3-1.4.tar.bz2
spandsp-20060903.tar.gz
I downloaded and installed the files in the follwing sequence
spandsp
libsupertone
libunicall
libmfcr2-0.0.3 is
2006 Mar 25
2
help on mfc/r2
Hello there!
I've problem with setting up unicall / mfcR2.
can't find proper notation for channel, trying unicall/1,
unicall/1/1001, unicall/g1, unicall/g1/1000
and still having no luck.
klaudia*CLI> !cp call /var/spool/asterisk/outgoing
-- Attempting call on Unicall/1001 for application Dial(363) (Retry 1)
Mar 25 09:29:34 NOTICE[19920]: channel.c:2429 __ast_request_and_dial:
2008 Jan 18
1
R2-Unicall Asterisk as CPE and as CO
Hi!
Im having some troubles trying to configure * as a bridge between a telco
and a pbx with R2, the scenario is this:
------------ E1/R2 --------- E1/R2 ------------
| Telco |-------------| * |-------------| PBX |
| (Telmex) | --------- | |
------------ ------------
I can receive calls from the telco
2004 Sep 23
10
MFC/R2
Hi all,
I have begun the release of my MFC/R2 protocol software. At
http://www.opencall.org/installing-mfcr2.html there are instructions for
installing what I have released so far. This is the MFC/R2 protocol
software, and a test program. The software to interface Asterisk to the
MFC/R2 code will be released shortly. It used to work, but it hasn't
been touched for a while, and Asterisk
2007 Jan 17
1
Asterisk + Unicall + Telmex E1 MFC/R2 Argentina + Meridian
Hi everyone!
I'm having some issue trying to place calls with asterisk connected to
an E1 R2 from Telmex Argentina. The other E1 port is connected to a
Meridian which also uses R2 protocol. Calls sometimes fail with
different error messages such as: Unicall protocol error 32773, 32772,
32769. Some other calls fail saying:
Far end disconnected(cause=Destination out
of
2007 Jul 17
7
Asterisk 1.4, Unicall and Nextel...
I have a customer that is complaining that any call coming in from
Nextel gives a fast busy. We are running Asterisk 1.4.7.1 with Zaptel
1.4.3 and all the MFC/R2 patches and libraries. All other calls go out
and come in, just Nextel seems to have this problem. The phone company
technician connected a PBX emulator on the line and that one could
receive the calls from Nextel.
The E1 is provided
2007 Jun 14
2
Unicall + MFC/R2 line dropped immediately after connect
Hi,
I am trying to set up an E1 line with CAS signaling using available
unicall patches with libmfcr2 implementation. Inbound calls works well,
I am able to get DNIS and ANI from incoming call, but I am still not
able to make an outbound call with our local carrier.
After tweaking of protocolvariant parameter in unicall.conf I was able
to find proper values for inbound and outbound calls, but
2007 Aug 23
1
libmfcr2 is giving definition error while compiling
Hi,
I am using debian 4.0 with version 2.6.18-4-686
I have downloaded the required files form site
asterisk-1.2.24.tar.gz
libmfcr2-0.0.3-1.4.tar.bz2
libsupertone-0.0.2.tar.gz
libunicall-0.0.3-1.4.tar.bz2
spandsp-20060903.tar.gz
I downloaded and installed the files in the follwing sequence
spandsp
libsupertone
libunicall
Till here it is compiling and
2006 Apr 21
1
Unicall MFRC2 Problems with BrT.
Hello All,
I'm facing problems with Unicall on this scenario :
CentOS 4.3 - Running on x86_64
Asterisk 1.2.7.1
Zaptel 1.2.5
When running zttool , shows all Spans OK.
But I can't receive and make calls.
I tried to change many parameters and still doesn't work.
Any clues ?
* unicall.conf
[channels]
language=br
context=incoming-pstn
usecallerid=yes
hidecallerid=no
immediate=no
2006 Feb 07
1
MFC/R2 in Brazil
I don?t know if the last message was with content. So, I sent again. I have
installed a Digium card TE210P and unicall for use MFC/R2. I think that it?s
all right but I can?t make and receive calls. I?m using asterisk 2.1 with
the patch made by Jos? P. Leit?o and the follow libs:
libsupertone-0.0.2
libunicall-0.0.3
libmfcr2-0.0.3
zaptel 2.1
My number is 34318300. The Telco send me only 8300.
2007 May 14
1
Asterisk and unicall + mfcr2 signalling
Hi,
I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I
have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I
can make calls over E1, but can't receive.
Here the CLI when I make a call:
-- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40",
"Unicall/g1/91642208|50") in new stack
-- Called g1/91642208
[May 14