similar to: No subject

Hi list, I'm having problems transferring certain calls made by the attendant between the PSTN and to an internal extension. Although, transfers between the majority of the calls ends successfully. Debugin this, I've found that calls made to certain "numbers" (Telephony Providers), aren't detected as ANSWERED in the CDR, so they are not properly accounted (for billing),

Hi list, I'm wondering if it's possible to transfer a call that is still ringing??? Actually, the problem is that my telco provider doesn't offer an uniform method for answer/disconnection supervision, and by that I mean, some of it's line (I think) offer a polarity reversal, but other lines (of the same service provider) do not offer anything at all, so the answer of a call

Hi list, I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap show" I get the message "*No such command 'zap show'*". I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the latest wanpipe too. zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know what's happening here!!! Any ideas???

I'm having (I think) timing issues in relation to bridged T1-T1 calls via dynamic spans. Fax calls are intermittently working, but voice is fine. My box has a Sangoma A400 inside it as the primary Zaptel timing source. My T1 PRIs that are hooked to the box come in via a foneBRIDGE2 (dynamic TDMoE spans). PRI #1 is the telco and PRI #2 is an existing Comdial FX-II. For some reason, bridged TDM

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hi list, I'm about to install Asterisk on an Old HP NetServer LC2000 Server (year 2001), it has 2 Pentium III 1GHz CPUs (Coppermine FSB 133MHz 256K L2 Cache), 768MB PC-133 ECC RAM, 3 UltraSCSI LVD2 18.2GB 10K RPM HDD in RAID5, 100Mb NIC for server. This Server will support 35 SIP phones (users) and 10 FXO ports (for telco lines) and 2 FXS ports (internal analog phones) with a Sangoma Remora

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

I'm having a problem receiving incoming faxes and I'm hoping someone here can help me out. My system is a PBX in a Flash with one dahdi card for my incoming analog lines and another dahdi card for my analog devices (fax and modem). My dahdi-channels.conf file looks like: ; Autogenerated by /usr/sbin/dahdi_genconf on Tue Jun 23 14:56:24 2009 ; If you edit this file and execute

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

Hi All This may be a silly question but... I have this dahdi_genconf generated file: ; Autogenerated by /usr/sbin/dahdi_genconf on Fri Jul 4 22:05:29 2014 ; If you edit this file and execute /usr/sbin/dahdi_genconf again, ; your manual changes will be LOST. ; Dahdi Channels Configurations (chan_dahdi.conf) ; ; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended ; to

I have Asterisk working with one FXO card (clone x100P card PCI card). I am trying to add 2 more cards so my question is - do I just increase the channel count on the zaptel.conf and zapata.conf files? [original] /etc/zaptel.conf fxsks=1 loadzone = us defaultzone=us /etc/asterisk/zapata.conf [channels] language=en context=from-pstn signalling=fxs_ks faxdetect=incoming usecallerid=yes

I am trying to configure Asterisk for BSNL, india network. I have successfully configured it for outgoing calls. When any outside number make any call to trunk then it receives the call properly but when the call is disconnected by inside extension then outside phone does not get a busy tone. Asterisk incoming call log: -- Executing [s at incoming:2] Dial("Zap/4-1", "Zap/1")

I've set up an outbound .call system for customer callbacks and the like. Calls are going out over analog lines and I'm trying to use the WaitForSilence routine to make sure the phone has stopped ringing before starting message playback. The problem is that if I set the first argument of WaitForSilence to anything other than 1, WaitForSilence never exits. Some general info on my setup:

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

Hi i have a tdm2400p and installed asterisk 1.4.11 with zaptel 1.4.5 im having an error message when in running asterisk with the tdm card in. here's the error from the console of asterisk: [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:7489 mkintf: Unable to get span status: Inappropriate ioctl for device [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:10466 build_channels: Unable to register channel

I'm in the process of setting up a 'phone tree', and are running into some problems. My goal is for users to dial a phone number, the asterisk system picks it up, plays the greeting, and users can type whatever they want into the system. What actually happens is users dial the phone number, asterisk picks up and additionally goes off-hook on another line, plays the greeting and

I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see anything in the changelog after the 1.4.5 release dealing with distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma A200 card. I enabled usedistinctiveringdetection in zapata.conf. However, on the Asterisk console, the output I get is: -- Detected ring pattern: 0,0,0 It would appear that Asterisk is

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

> I have 2 FXO channels from which I want to route incoming calls to > different contexts in extensions.conf. I edited the context entries in > dahdi-channels.conf and created matching entries in extensions.conf. > One channel is routed to the new context as I want, but the other > channel is stuck going to the default "from-pstn" context no matter what > I do. >