similar to: Zaptel update trouble

hi every body; i installed zaptel 1.4,libpri 1.4, asterisk 1.4, asterisk-addons 1.4 succefuly, but i can't find the command "genzaptelconf, so i tink to install "handy zaptel toolset" please can someone tell me whitch package goes with zaptel 1.4, i consult "http://updates.xorcom.com/rapid/pool/main/z/zaptel/" but ????????????

Hi all, We're planning an Asterisk implementation consisting of two SC1425 Dell Servers using Digium T1 cards and SATA drives. The problem I'm having is the only PCI slot shares an IRQ with the SATA controller. Any altering of one device's IRQ takes the other device's IRQ with it in lockstep. I've disabled all non-essential integrated devices with no change. I'm a

Hi List; I am facing a problem relaed to menuselect when I am trying to compile zaptel -1.4.2.1, the error as following: [root at localhost zaptel-1.4.2.1]# make linux26 make[1]: Entering directory `/usr/src/asterisk-1.4.4/zaptel-1.4.2.1/menuselect' make[2]: Entering directory `/usr/src/asterisk-1.4.4/zaptel-1.4.2.1/menuselect' make[3]: Entering directory

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

I finally got Solaris to successfully make asterisk, using these instructions: http://sunfreeware.com/programlistsparc10.html#gcc33 Now though, when I issue the make install, I get this error: mkdir -p /var/opt/asterisk/spool/system mkdir -p /var/opt/asterisk/spool/tmp mkdir -p /var/opt/asterisk/spool/meetme install -m 755 asterisk /opt/asterisk/usr/sbin/ install: asterisk was not found

Sorry about last posting, typo... I just added 2 Digium X100P cards. When my * box boots, it found them and configured them. When I enter genzaptelconf, it comes back with the following error: line 13: Unable to open master device '/dev/zap/ctl' Unloading zaptel hardware drivers: Removing zaptel module: rmmod: module zaptel is not loaded

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Hi Version 0.9.0 of Xorcom Rapid Debian/GNU/Linux/Asterisk has just been released. Main changes: * A decent version of Asterisk/Zaptel (1.0.2) is provided * Includes a better default configuration * Automatic detection of the most common Zaptel cards * Contains more optional software (apache, MySQL, Webmin and others) - available via menu You can get it from:

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver? Att Vin?cius Fontes Desenvolvimento Canall Tecnologia em Comunica??es Ltda.

Greetings to all list members! My name is Aldo Sudak and I am an Asterisk newbie. I am writing now because I have not been able to find any mention to the issues described below, neither in this list nor in the wiki. I am performing preliminary tests with Asterisk 1.4.11 and Zaptel 1.4.5.1 on Fedora Core 6. Installation of all of the Asterisk packages was straightforward and I always obtained

Hello, it is now 2am presently where i am and i have been at work since 8am yesterday. I am not allowed to go home unless i get this system up and running, else i shouldnt expect a job when i come back :s... now that you have some background, I am having no luck installing these two cards - i have already confirmed they are on their own IRQ etc, and if i run genzaptelconf, they are coming up

Hi can anyone help. I just updated my CentOS and ran the command rebuild_zaptel and genzaptelconf with a Reboot in between each step. Now I have no Zaptel devices (I used to have 3 FXO X100P Cards) Summary of what happens below: (Zaptel.conf contains no card info after running this command.) Many thanks in advance, Richard ---- STOPPING ASTERISK Disconnected from Asterisk server

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

Things consider problems with sftp software - sftp manually first time to accept the fingerprint and anytime software is updated on host. - no ascii mode only binary - no verbose or indication of bytes transfered (you would do an ls after sftp is done) - no mput or mget (this may be a show stopper) but could script could generate itself with all the filenames takes coding. Kenneth

Hi pals, Pardon me if this question sound basic please. This is the first installation where I have to use the analogue card and therefore a little lusty. I have googled a lot, but though there is a lot of information about the above file, none indicate where the file lives. I have a installed asterisk and zaptel software on a fresh installation of CentOS 5. This all from source and following

hi i'm trying to configure a TE205P on asterisk@home i've edited /etc/sysconfig/zaptel adding this line: MODULES="$MODULES wct2xxp" now, when the system is loading, i can see that the wct2xxp module is loaded correctly but if i try the command: /usr/local/sbin/genzaptelconf i get: STOPPING ASTERISK STOPPING FOP SERVER Generating '/etc/zaptel.conf' Generating

hello my friends, when i make a genzaptelconf i get this message ******************** CAS signalling on span 2 conflicts with HDLC with FCS check on channel ******************* Any idea Please? I m installing zaptel 1.4 i checked in "http://bugs.digium.com/view.php?id=7860" that it's a bug but beacause i m a newbie in asterisk i can't undrestand what exactly mean Thank You