similar to: open up firewall ports for Asterisk - safe?

Hello, using Asterisk 1.4.28, I encountered a problem with SIP RTP port allocation. I found some entries in mailinglist and bugtracker regarding this issue, but only old ones. My rtp.conf has [general] rtpstart=30000 rtpend=30100 so 100 ports available. I know that up to 4 ports per channel can be used and so up to 25 channels are possible. But even earlier I often get the error about

After getting some ERRORS like this: [Oct 8 21:42:49] ERROR[31903] rtp.c: No RTP ports remaining. Can't setup media stream for this call. [Oct 8 21:42:49] ERROR[2485] rtp.c: No RTP ports remaining. Can't setup media stream for this call. [Oct 8 21:42:49] ERROR[31903] rtp.c: No RTP ports remaining. Can't setup media stream for this call. [Oct 8 21:42:49] ERROR[2489] rtp.c: No RTP ports

Hi to everyone! I have succerfully instaled my new Asterisk 1.4 on my debian etch. I have my users in sip.conf like this: [200] type=peer host=dynamic context=home secret=200 callerid= 200 dtmfmode=rfc2833 nat=yes mailbox=200 at home disallow=all allow=ulaw I can make calls in my LAN but i can?t ear comunications with another client trought Internet. My Asterisk is in my LAN and i not have a

On 2/23/19 4:19 PM, Joshua C. Colp wrote: > On Sat, Feb 23, 2019, at 11:04 AM, hw wrote: > > <snip> > >> >> directmedia is not explicitly enabled; I guess it's the default. >> >> Joshua basically says there is no way to control which ports are being >> used for SRTP because that it is "up the endpoint". Such endpoints, in >>

Hello. I'm trying to test an Asterisk server by using a VOIP provider for international calls but, I'm having problems trying to get my server communicate with theirs. I don't know if I'm having all these issues becuase I'm behind NAT or what. I have the following in my server's sip.conf: [provider] type=peer host=<theprovider's server> username=<username>

We are trying to use a softphone from a location that is behind a firewall. We are using x-lite as the softphone. So far, we've been able to get the phone to register with the asterisk server, and it can receive voice from the asterisk server (IE, voicemail, etc). However, asterisk can't hear anything from the softphone. We have used 2 different machines to test this on. We are watching

I've got a ShoreTel 210 MGCP phone drops calls. My packet capture indicates that the phone may be trying to renew its registration with *, but reports Restart Method of Disconnected (frame 2), then * seems to take that as a sign that it has lost the connection and closes things down. The phone, meanwhile, seems to think it can continue the conversation until a few ICMP "port

To Jonas: I have an asterisk box at home and I have this line in my rtp.conf file: rtpstart=10000 rtpend=10100 And My FW is setup to forward all incoming ports of range 10000-10100 to the asterisk PC. I've never had a problem since one year, but I have never received more than two simultaneous calls with SIP clients. Message: 5 Date: Fri, 13 Sep 2013 11:49:59 +0200 From: Jonas Kellens

Asterisk 11.1.0 Various soft-phone SIP clients call center with 10-12 agents online at once using asterisk queue Occasionally an agent will get a call (or more often a series of calls in a row) where neither party can hear the other, or can only hear each other sporadically. A MixMonitor recording of the call plays only the caller - none of the agent's audio is heard in the recording.

I see in sip debug it says Audio is at port 10342 Express Talk suggests Audio at UDP 8000-8020 I've tried changing Express Talk to 10000 and forwarded 10000-10400. Is there a possibility Express Talk won't work in the 10000 range? Is it possible to limit Asterisk to 8000-8020? Thank you, Gary

Hi D'arcy Have you checked your RTP port ranges (I'm sure you have), and also that the server IP for RTP as specified in the initial SIP is correct? Not sure how this will relate to your setup, but we had something similar here using Asterisk 1.8.11.0 on both sides of the connection, via a VOIP service provider in the middle. We had slightly different parameters, e. g. that we would

I'll start by saying I'm a trixbox user, and a new one at that, so hopefully you can respond to me on those terms. I have a user who works from home 1 day a week. On that day I'd like for him to be able to connect with a softphone and be reachable by just dialing his extension as we normally would. I could set him up a new extension, then he could forward his phone there on

hi all ! we've got IAX2 protocol working between several Asterisk servers. Now we are concerned with doing bandwidth management to maintain an acceptable voice quality. We thought of prioritizing the udp traffic. ( Giving a high priority to those IAX2 udp ports.) I know that IAX2 uses udp/4569. Is there any other traffic/ports that we need to consider for bandwidth shaping w.r.t IAX2.

Hi again, list! I know, I'm really annoying the list... :) Well, maybe I got my Asterisk at home ("wrt" on the previous E-Mails) to accept my mobile phone from Internet. It was a problem with the network and the firewall. Now I can log my mobile phone in my Asterisk in and the phone is REACHABLE. Wow! Got it! If I call a phone at home using my cellphone it works and the

Hi all, Iam using asterik 1.4.8 and connected to google talk. When iam calling from my google talk account to sip phone i can hear the voice (2 way). (this happens only within the LAN). when my friend tries to call my asterisk server (connects to the public ip) using his googletalk client it comes to my sip phone but either party cant hear a voice. I have fully allowd both tcp,udp on my

I have been encountering a rather hard to debug problem for the last couple of months: * Calls are setup fine. * After a couple of minutes, two way audio becomes one-way and the remote or local party drops out of the call. Setup: * Nokia E71i sip on NAT'd network (multihomed linux box) * Remote asterisk 1.4.21 on Ubuntu on public network * using a Finera/Betamax provider to route calls to

Hey there i'm trying to get an Asterisk 11.11 with encryption working with my Grandstream phones. But i stuck. To avoid NAT problems i'm using IPv6 Just with TCP/TLS it's working fine. Only the SRTP funktion is not working. Asterisk tells me WARNING[6938]: chan_sip.c:3906 __sip_xmit: sip_xmit of 0x7fa10800f5a0 (len 681) to [2a02:1205::...]:37635 returned -2: Success and also SSL

Hello I'm having a difficult time finding precisely what to put in sip.conf and extensions.conf (and possibly other files) to get a working configuration to connect an Asterisk (1.4) server to a VoIP provider with the Asterisk server + SIP clients located in a private LAN behind a NAT router: http://img560.imageshack.us/img560/3749/asterisknat.png Would someone have a full, direct (ie.

Hello users, I am trying to integrate asterisk and gtalk. my configuration is as follows OS:centos asterisk-1.6.0 asterisk-addons-1.6.0 dahdi-linux-2.2 dahdi-tools-2.2 libpri-1.4 share iksemel-1.2 #/etc/asterisk/jabber.conf [general] debug=yes autoprune=no autoregister=no [google] type=client serverhost=talk.google.com username=XXXX at gmail.com secret=xxxxx port=5222 usetls=yes usesasl=yes

Hi All, I am using Asterisk for one of my projects in OpenBTS. I am having the age old problem of "extension not found" when try to make a call from one registered SIP phone to other registered SIP phone (two mobile phones connected to Asterisk via OpenBTS). The exact error thrown on Asterisk CLI is *"chan_sip.c:20039 handle_request_invite: Call from [IMSI310410270465840] to