similar to: chan_isdn with HFC-compatible

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hi all, I have a "Cologne Chip Designs GmbH ISDN network controller" and I want to terminate voip calls via this ISDN card. My question is: How I must to wire the ISDN equipment with my ISDN card? With normal cable or crossover? How I can to check if ISDN card is linked with ISDN equipment? In this moment I have 1:1 cable between ISDN's, the mISDN is installed and "misdn

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hello, I'm trying to set up a b410p rdsi card, and I'm having problems getting it up. I followed the instruction on asteriskguru and everything seem to be fine but all leds on the card are in red. [root@rdsipbx ~]# uname -a Linux rdsipbx 2.6.15.7 #2 Tue Jun 5 16:37:07 CEST 2007 i686 i686 i386 GNU/Linux [root@rdsipbx ~]# dmesg |grep Digium HFC-multi: card manufacturer: 'Cologne Chip

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Hi Guys. Hope someone can point me in the right direction. I would like to get into LXC and evaluate its usefulness compared with Linux-VServer. I notice that LXC is in tech preview upstream, however I am at a dead end trying to figure out how to get started. I cannot find any usertools in the rpm's that ship with CentOS 6. Is this because the tech preview requires me to get the tools

Hello, Sorry about the last email, I just found the shortcutkey for sending, by mistake :-( OK. I am a windows user and I wanted to instal emacs. However, went to speak with the information staf on the institut and they told me that that is a bit problematic sometimes, and that there is a free soft that could do a very similar job which is crimson... This is like a note pad, but highlights the

We have ISDN PCI Adapter from Billion(using mISDN). When we connect it to the PSTN the incoming calls are OK. When we try to make a call we can't do that because the ISDN port is Down: CLI> misdn show port 1 BEGIN STACK_LIST: * Stack Addr: 40400001 Port 1 Type TE Prot. PMP L2Link DOWN L1Link:DOWN Idx: 0

Hi guys, I'm hoping I've made a silly mistake here, but I've been staring at the screen for the past few hours and I can't work it out. I upgraded to 1.2.16 recently, and am having problems with zaptel. The card is detected, I get a reasonable output from ztcfg -vv, and zttool shows the installed module (TDM400) with one FXS module. But when I start asterisk, I get

*Good morning! * *I verified that the trixbox version Trixbox 2.6.1.13 has support for OpenR2, I verified in the repository that has to libraries of the project openR2, but I don't manage to do to work in the trixbox, when I type the command (it colors show channeltypes)ele no demostra the support to MFC+R2, they could help finding out which package is necessary of the trixbox and which the

Hello, I have an Asterisk 1.8.11 installation. When I built up this Asterisk, I didn't install DAHDI channel, if I issue command connect*CLI> core show channeltypes I would have response like: connect*CLI> core show channeltypes Type Description Devicestate Indications Transfer ---------- -----------

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Dear all, I'm using Asterisk 1.4 as my SIP server of my LAN users. The SIP clients are using different operating systems such Debian, Gentoo and Windows XP so they use different SIP softphones like SJPhone, Twinkle and X-Lite. In order to let SIP clients to see the presence status to each other, do I have to establish any special setting in Asterisk 1.4 ??? Or the presence status (online,

Hi Guys! I got a Diva passive ISDN card and I can't get it work with asterisk 1.4, It is supported in the kernel as an isdn4linux device but I can't find "Modem" channel type when i type in: core show channeltypes. I'm guessing it is removed in asterisk 1.4. Tried with capi interface but it does not work :( Anybody got some idea how can i make it work or got a link to a

Hello all, I have seen some people asking how to configure asterisk to work with h323 but i did not manage to do fix it yet (i am not an asterisk expert). Can someone help me configuring asterisk? It is already compiled asterisk 1.4.5 with H323 support. Everything looks fine. Then i understand i need to configure several files: -sip.conf -ooh323.conf -extensions.conf do i also need to configure

Hi, I installed a 1-port FXO on my Ubuntu 8.4. I was earlier only hearing a fast clicking sound and now I am not hearing any dial-tone. The FXO card has 2 slots: [phone | line ]. I hve connected the wall-phone-input to the "line" slot and "phone" to my home-phone. I do not hear any dial-tone on my home-phone. Asterisk seems to recognize my hardware....here are the relevant