similar to: Need advice to get wcte11xp and wcfxo to load

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

I have two X100P cards that were working just fine for months. When I run modprobe wcfxo today I got the following error: ZT_CHANCONFIG failed on channel 2: No such device or address (6) /lib/modules/2.4.19/misc/wcfxo.o: post-install wcfxo failed /lib/modules/2.4.19/misc/wcfxo.o: insmod wcfxo failed The output of dmesg said that wcfxo:Out of space to write register 06 with e0. What?s

I found similar posts regarding this error but none that answered my question. My zaptel.conf reads: fxsks=1-2 fxoks=3 loadzone=us defaultzone=us and /proc/interrupts: CPU0 0: 5542402 IO-APIC-edge timer 1: 2 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 3 IO-APIC-edge rtc 14: 72582 IO-APIC-edge

This is a system for our lab. I have no problem getting rid of X100P clones. But I am just curious why can they work. Even the drivers are not loading correctly. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List -

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Hi there my zaptel hardware is giving errors while loading but they seem to load just fine. the lights wil work and my wctdm card is also workin and the isdn works to But when I stop asterisk I have to reload al cards again is this normal? This is my zaptel.conf is there no way to group these because my te110p is giving an error that it can't find channel 35 but 35 belongs to my wctdm.

Hi, using Sangoma drivers: - doing 'lsmod', I see: zaptel ... wanpipe,wctdm24xxp,wctdm,wcfxo,wcte11xp,wct1xxp,wct4xxp,tor2 I'd like to avoid loading all these modules. What have I to do? - do I need to have 'zaptel' startup script under /etc/init.d ? Thanks -- Domenico Viggiani

Hi people, I'm having some problem when I reboot my machine. Every time that I reboot the system, the zaptel changes the order loading of the cards. I have 3 cards (wcte11xp, wctdm and wcfxo). So, my configs in the zaptel.conf will be always wrong, because I change the config for a order loading, and when I reboot its change! I tryed to see the config in /etc/udev/ but I think its right,

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

Hi List, I am having some trouble with installing the latest version of ztdummy on a CentOS Kernel 2.6 system. I have installed a few Asterisk systems on Slackware Kernel 2.4.x without any issues, unfortunately there is no choice about this distro, or kernel as it has been preinstalled by someone else. And so I am in the dark with an unfamiliar distro and kernel. I am fairly sure the

Hello List, i am trying to set up an * box with a debian 2.6.10 Kernel. the compilation of asterisk and the zaptel drivers worked almost perfectly. so i did modprobe zaptel modprobe wcte11xp (which is the correct driver for my card) ztcfg -v and this results in ZT_SPANCONFIG failed on span 1: No such device or address (6) I don?t have any ideas whats wrong. google was no help, checking sources

I originally built my Asterisk server without installing the Zaptel package as it was going to be a purely SIP based system. However when I went to setup conferencing using meetme I found out that app_meetme is dependant on the ztdummy for timing. I have now installed the zaptel package and I believe the ztdummy module is loading ok [root@astro asterisk-1.4.0-beta2]# lsmod Module

Hi all, What hell hapen here? asterisk:/etc/asterisk# /etc/init.d/dahdi startLoading DAHDI hardware modules:FATAL: Error inserting dahdi (/lib/modules/2.6.26-2-686/dahdi/dahdi.ko): Device or resource busy wct4xxp: done wcte12xp: done wct1xxp: done wcte11xp: done wctdm24xxp: done wcfxo: done wctdm: done wcb4xxp: error wctc4xxp: done xpp_usb: doneError: missing /dev/dahdi! When

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

[root@server ~]# modprobe zaptel [root@server ~]# modprobe wcfxo ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install command for wcfxo [root@server ~]# ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address

Hi, is it possible to set a wcte11xp card to use a certain IRQ? I've tried a few things but it always shares the IRQ with eth0 even though the system has 4 spare ones. I can't set it via the BIOS. Regards Lee -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050902/9ce217db/attachment.htm

/bin/sh: -c: line 0: syntax error near unexpected token `;' /bin/sh: -c: line 0: `if [ -n "" ]; then if [ -f ]; then mv -f .bak ; fi; cat .bak | grep -v "alias char-major-250" | grep -v "post-install torisa /sbin/ztcfg" | grep -v "post-install wcfxsusb /sbin/ztcfg" | grep -v "alias wctdm" | grep -v "post-install wctdm