similar to: E1 not coming up

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

Any ideas? Sangoma support is closed for the evening. I have the latest Sangoma drivers and Asterisk 1.4 everything installed. When I fire up asterisk, I keep getting "Primary D-Channel on span 1 up" repeated over and over. The B channels never come up. There are no errors in any of the logs, zttool, or the wanpipe tools. Intense pri debug output: < Unnumbered frame: < SAPI:

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi Guys, Running the following with a Sangoma A101D PRI card: *Asterisk 1.4.21.2* *LibPRI version: 1.4.10* No inbound or outbound calls can be made. In fact Asterisk CLI doesn't show any activity. Problem goes away on restart of the system or maybe asterisk. I see post about upgrading Libpri to 1.4.10.2 and then I see posts that even that didn't work. Anyone can weigh in this please?

Hi, I have the following happen to me after the restart of one of my servers: out of my 3 PRIs (all configured with the same technical settings), the last one isn't coming back. It's underutilized (chances it didn't get a call since my reboot), if it makes a difference . The PRI goes from provisioned to unprovisioned, and I get this regularly: [Jun 22 09:03:48]

Hi everyone, I'm trying to get a Sangoma A101D-X card talking to a Sasktel PRI (Megalink) circuit and having some trouble getting it to handshake. Thanks for any help or suggestions to diagnose this problem. The problem is that Asterisk has trouble bringing up the link. I see the following lines every couple of minutes: == Primary D-Channel on span 1 up == Primary D-Channel on

Hi, I am trying to validate a setup with a sangoma A116 card (16PRI in one card). I currently have two machines set up, each with a sangoma A116 card. Those are interconnected with crossed PRI cables. One of them is in NT mode, the other in TE. The ports are configured in E1 mode, asterisk is all set up and I can make calls between them, filling up all 480 (16 * 30) channels. Now, I learned

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

Hi, I'm trying to install an E1 PRI, and I need it working by Monday, but although everything seems ok, I get no response to calls. When I make a pri extense debug on span 1, I repeatedly get the following: Sending Set Asynchronous Balanced Mode Extended [ 00 01 7f ] Unnumbered frame: SAPI: 00 C/R: 0 EA: 0 TEI: 999 EA: 1 M3: 3

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

I've got a couple of PRIs coming in from a SUMA 4 switch with some 800 numbers routed through it. When the calls come in, I get the following message on the console and the call never makes it through: (800 number is fake) Extension '8005551212' in context 'nonauthenticated' from '232102749585' does not exist. Rejecting the call on span 4, channel 1. I do have the

Hi, I'm pulling my hair out, cause cannot connect to EuroISDN BRI in Italy with octobri card from Beronet. I use bristuff and have following zaptel.conf... # # This file is parsed by the Zaptel Configurator, ztcfg # # # First come the span definitions, in the format # span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow] # # The timing

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

Hi list! We currently have a PRI gateway composed by a box with two Digium quad-span PRI cards (a TE420 and a ). One of the cards is filled with TELCO1, while the other has first two slots filled with TELCO2, and 3rd slot with TELCO3. I am currently having (timer ?) issues on TELCO3 (span 7) D-Chan (202 as determined by dahdi_genconf ) is constantly failing causing on-going calls to terminate.

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi, I'm having problems with a new ISDN PRI in a new server. The cable is connected and the E1 modem seems to have issues with syncing (blinking light on the modem). versions: CentOS 6, asterisk 1.6.2.20, dahdi 2.5.0.1, libpri 1.4.12 ------------------------------------------------------------------------------------ dahdi show status T4XXP (PCI) Card 0 Span 1 RED 0

Hello, I have a problem with Asterisk, on 10% of incoming calls the IP Phone ring but I don't hear the caller and the caller doesn't hear me (all IP Phones have the same problem). This problem appear also if the call is directly send to the second E1 of the digium card who is connected to an IVR. It does not depand on the charge of the server (I have the problem with only one call).