similar to: Asterisk + Legacy PBX

Hi I've bought the Wildcard TE110 some days ago but I'm unable to get it to work with Siemens HiCom 300. I've tried this so far: 1. I've used standard cat5 cable cut off on one edge and twisted wires 1 to 4 and 2 to 3 which is according to cisco a short circuit for E1 lines. Wildcard takes a few seconds and sets the link to green (OK). 2. I've tried to connect our running

Before studying your configs, what have you tried so far? Did you change this? Also, try changing your second span timing from span=2,2,0,ccs,hdb3,crc4 to span=2,0,0,ccs,hdb3,crc4. Here is the documentation on voip-info for why it may be the cause of your issues http://www.voip-info.org/wiki/view/Zaptel.conf+span+syntax span definition format:

Hi, I am looking to integrate Asterisk with a Siemens HiCom 150e via BRI and wondered if anyone is able to offer any advice. In simplistic terms, my goal is to pass calls from the HiCom to the Asterisk box. e.g: HiCom user dials access code and can call Asterisk extension or establish SIP call over Internet. Likewise, I'd like Asterisk to be able to present a call to the Hicom, either

Hi I try to connect my asterisk with a Siemens Hicom pbx. I have a PCI cologne Chip card wich support NT mode. I have compiled mISDN driver, and I use chn_misdn from debian package. The card wotk fine in TE mode but mot in NT mode. for informations : routeur*CLI> misdn show stacks BEGIN STACK_LIST: * Stack Addr: Uid 40200001 Port 1 Type NT Prot. PMP Link DOWN --> bchan: addr 0 channel

I have a strange problem with overlap dialing. I installed an asterisk server between a Siemens HiCom PBX and our telephony provider. Everything is working fine except some strange problems with the dialing of the fax (connected to the HiCom PBX). It seems to me that if dialing takes too long Asterisk just hangs up the channel without recognizing that the fax machine is still dialing: (Fax gets

Hi list, My Asterisk config for outgoing calls is the following: exten => s,1,Dial(SIP/${MACRO_EXTEN}@voipprovider,60,g) exten => s,n,GotoIf($[\"${ANSWEREDTIME}\" = \"\"]?pri:hang) exten => s,n(pri),NoOp(Problems with voip provider trying PRI) exten => s,n,Dial(Zap/g2/${MACRO_EXTEN},60,g) exten => s,n(hang),HangUp in most cases it works well but, if my

Hi steve and All, I'm attaching cat proc/interrupts out put, lspci -bv out put, zapa.conf, zaptel.conf for your information Thanks so much for the feedback and I do accordingly. Hope to get rid off this isue any how. To day also reported 10 call drops within 2 hours of period. fook forward to have your support on this regard. Thanks & Regards, Vidura Senadeera, Network Engineer,

Hi Everyone, Got a setup as follows: Telco ----> Siemens HiCom 300E <----> Asterisk1 <----IAX2 Trunk----> Asterisk2 <----> Siemens HiPath 4xxx The solution works except for one problem. Incoming calls from the telco get redirected to the Asterisk1 box with the correct extention, only if there is a callerid set on the call, the Asterisk1 box drops the call (it doesn't

Hi, Is is possible to implement this: Hicom150 --- BRI (QSIG) ---- Asterisk I've been reading Siemens documentation and they say: "Digital nailed connections Corporate communication networks can be implemented over digital S0 or S2M nailed connections between several Hicom systems using the CorNet N protocol and between Hicom and non-Siemens systems using the QSig protocol. The

Hello all, I have the following working (somewhat) setup: TELCO | | E1 (30 Chan -- TE210 SPAN 2) | | Asterisk box 1.6 with DAHDI drivers loaded Digium TE210p | | E1 (30 Chan -- TE210 SPAN 1) | | NEC PBX

hi, we are currently planning are large site which will migrate from an old siemens hicom pbx to asterisk. it will be a slow migration, the asterisk server will be inserted between the telco E1 and the hicom. new phones will be sip ones. the customer has several fax machines and analog phones (some of them have to be explosion-proof). around 50 analog ports in total are needed. as we are in

Hi * :-) I found in the online WiKi docs some information on how to integrate Asterisk with "old PBX"... http://www.voip-info.org/wiki-Asterisk+legacy+integration ...but I couldn't find anything on integration with a Siemens HiCom 150E. Later on we'll migrate to a HiPath 3750 so information covering this model would be nice too... Do you know if any of the PBX listed

We are using MFC/R2 driver successfully in at least three places in Brazil. I have problem with an Asterisk integrated with MFC/R2 with a Siemens Hicom 300. I can get a good audio quality with Grandstream, Polycom, and X-Lite softfones, but SIPURAS and Linksys get a garbled audio, something like a "Darth Vader" voice. We have tried everything in Sipura. The SIPURA 2000 and the Linksys

Hello, we have a PRI (E1) to a carrier and a second one to a legacy PBX: DTAG ---pri---- * ------ Hicmo (PSTN) | | Sip and more Many normal inbound calls are direcly routed to the hicom. Outbound calls from the Hicom go through LCR and then to PSTN. Inbound faxes are working, but outbound faxes from hicom to pstn are

Hi I've got an Asterisk box connected to a Siemens Hicom 300 using a Digium TDM400. The Hicom provides the calling extension as DTMF at the beginning of the call followed by two *, as in 3425** when 3425 calls my extension, I can hear all 6 tones if I have a handset connected but using Asterisk's Read application straight after Answer() Asterisk usually only gets the last *, sometimes the

Greetings, asterisk list and community, I have a problem in how our telefon switch (Siemens HiCOM) "talks" with my new configured Asterisk server (V.11.18.0) without my Asterisks server in the middle.... <phone> <--> Siemens HiCOM <-ISDN-> NTBA <-...-> PBX Telekom A phone connected to the switch requests an "Outgoing" line by dialing "0".

Hello, Actualy I have got a PBX conected to a BRI port on a Cisco Router witch route the calls. The router is using h323 with the other end. How could I replace the actual PBX and pass all the calls to the router, as now works. I tryed connecting an asterisk CAPI port against the same BRI Cisco port, but I can not make any calls, I get the following error from asterisk. Connected to

the Telco, I can make calls in. What I am trying to get though is how to pass through the DID range. The E1 that I am connecting to the Telco with, used to connect direct to the NEC system and already has hunt group calling enabled for all 30 channels. Also, I was given a 100 number indial range (from 00 -> 99). If the E1 is connected to the NEC directly, I can call 5555 7320 and the NEC

Hello all, I really checked voip-info.org but it still seems to be not very easy and I just hope that there is anybody with a simular config. We have one PRI (euroisdn with 30 channels) coming from the DTAG. The second PRI should be connected to a Siemens Hicom 150E Pro Office PBX (was cheaper than a channel bank :-) Carrier ----S2M------ * -----S2M------Siemens | |

Hi, I have a server with 2 TE110P cards. 1 card is plugged to telco line, another card is plugged with a Hicom PBX. I want to send some call to VoIP phones and all other to my PBX. I don't known how to make my dialplan : ===========Extensions.conf========== [incoming_call] exten => 090200000,1,Goto(callcenter,100,1) exten => 022956353,1,Goto(callcenter,100,1) exten =>