similar to: b410p

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hi all, I have a "Cologne Chip Designs GmbH ISDN network controller" and I want to terminate voip calls via this ISDN card. My question is: How I must to wire the ISDN equipment with my ISDN card? With normal cable or crossover? How I can to check if ISDN card is linked with ISDN equipment? In this moment I have 1:1 cable between ISDN's, the mISDN is installed and "misdn

We have ISDN PCI Adapter from Billion(using mISDN). When we connect it to the PSTN the incoming calls are OK. When we try to make a call we can't do that because the ISDN port is Down: CLI> misdn show port 1 BEGIN STACK_LIST: * Stack Addr: 40400001 Port 1 Type TE Prot. PMP L2Link DOWN L1Link:DOWN Idx: 0

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

hi list, I'm currently trying to get Asterisk running with an HFC-compatible ISDN card (no-name product, but supposed to work with Asterisk according to the packaging). the ISDN-card is connected to a alcatel ISDN-system where it should act just like a normal ISDN-phone. I went with http://www.misdn.org/index.php/MISDN_with_Asterisk and installed the package from beronet.com including:

Hello I have just set up Asterisk Asterisk 1.4.21.2 on a CentOS 5.2 machine. I am using the OpenVox B200P ISDN card. My problem is that even though chan_misdn module seems to be loaded correctly with Asterisk (I can see it using 'module show' command) the misdn commands are not available to me in the CLI so I cannot tell if my box is correctly interfacing with the ISDN card Any ideas

Hi all, we're buildin an Asterisk box based on an Intel IXP425 board. The board uses a Beronet BN2S0 ISDN card, mISDN 1.1.4 and asterisk 1.4.2. hfc_multi has been patched to compile under big endian cpu, and so also capi kernel files. All the modules seem to load correctly (configuration was made with misdn-init config), but when starting cha_misdn, asterisk outputs the following lines: P[ 1]

Its been a few days, I was wondering if anyone else has any ideas on how to get this to work? If not, could I ask a the direct question as to if anyone here has (or knows someone who has) successfully got something like a Cisco Router to successfully establish an ISDN data/Internet connection through the Asterisk PBX?

I am working on a Rails app where people sign up and have a profile. When they are first signing up, they fill in their profile but I have an additional question when they are creating their account that alters the initial configuration of the account but is never used afterwards, so I don't want to include it in the profile. It is a multiple choice question with certain validation rules.

When joining our Solaris 10 Samba 3.0.23 system to ADS via... # /usr/local/samba/bin/net ads join -U Administrator Administrator's password: Using short domain name -- ULS Failed to set servicePrincipalNames. Only NTLM authentication will be possible. Please ensure that the DNS domain of this server matches the AD domain, Or rejoin with using Domain Admin credentials. Joined

Hello list. I'm trying to rebuild the 2.6.9.67.0.20.EL kernel, but it fails even without modifications. How did I try it? Created a (non-root) build environment (not a mock ) Installed the kernel.scr.rpm and did a rpmbuild -ba --target=`uname -m` kernel-2.6.spec 2> prep-err.log | tee prep-out.log The build failed at the end: Processing files: kernel-xenU-devel-2.6.9-67.0.20.EL Checking