similar to: TDM bus extension.

Hi, one month ago, I announced, that I will look at the openss7 project in order to use it together with asterisk. It took a while for me to check the capabilities of and around the project. Since the openss7 project consists of only one person, and when there was just silence for a long time in the project's mailing list, I doubted, whether it was a good idea to consider using openss7. In

Hi, Does Asterisk support SS7? Google shows an old new post from Feb. 2002 stating that OpenSS7 would help add SS7 support to Asterisk, but presently OpenSS7 seems to be dead and I can't seem to find anything about it at Asterisk or Digium's sites. What happened? -- Regards, Tais M. Hansen ComX

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

Hi, I've posted this question on OpenSS7 mailing list but I didn't get a clear answer. I have a system running asterisk using Digium T400P card. Can this same card be used with OpenSS7 project to carry SS7 links? Is there any difference between these two cards? -- Matteo D'Amato Network/Telecom Administrator Intelco Communication Inc

Hi, there are still some questions to be answered by OpenSS7.com in order to decide, whether E400P-SS7 is a good choice for the asterisk SS7 support. In the meanwhile I'm also in negotiations with another manufacturer (whose name I currently may not tell due to a NDA) of SS7 hardware, who gets likely persuaded to offer a cheap SS7-PCI-card which would be suitable for asterisk. Asterisk users

Hi, Is this card the same as the T410P, after all, it's made by Digium. There's one prior reference on the mailint list[1] but it didn't answer the question. There was also an SS7 status report[2] last June but it's doesn't seem to have lead anywhere either. There was post saying an SS7 release was immenent last September[3], but then silence. Any info anyone would like to

Hi all I installed DAHDI Version - 2.6.1 DAHDI Tools Version - 2.6.1 libss7-trunk Asterisk 11.0.1 from source on Fedora 12 x86_64. Now i`m unable to load chan_dahdi and libss7: myserver*CLI> module load chan_dahdi.so ?ERROR[10124]: chan_dahdi.c:17842 process_dahdi: Unknown signalling method 'ss7' at line 37. myserver*CLI> module load libss7.so Unable to load module libss7.so

Hi Team, i have been facing issues with sangoma card with 16 E1. used LibSS7 asterisk 1.6 with 8 E1 the links are stable , but moment i add another card of 8 E1 for to support 16 E1. link keeps fluctuating any idea why ? Please help Thanks Vinod Dharashive -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello.. I have a customer who wants to connect 2 PBX's over IP.. The setup should look like this: [PBX] <-- SS7 --> [Asterisk] <-- IAX --> [Asterisk] <-- SS7 --> [PBX] Since there are no SS7 cards , I was thinking at a way of carrying the E1 data as bulk...Can I do that ? How ? Is possible a scenario like this ? I'm thinking of IAX because I don't

Hi all, Does somebody know what's new with SS7 and * ? I'm very interested. Is it ready ? I'm prepared to pay if necessary. Thanks, Angel.

Hello, Is it possible to transfer ss7 signaling over an FXO interface. I need to setup an ss7 test system composed by two Asterisk based IP-PBX systems with anlog interfaces only (FXO and FXS). I want to know if it is possible to connect the two IP-PBX as following: - FXS interface in PBX1 -----------------> connected to -----------------> FXO interface in PBX2 =============>

Has anyone tried to get dialogic ss7 trunking to work with Asterisk? I did some googling but nothing helpful turned up... Could a person get an intel dialogic and get * to see it like a zap channel? And use it for incoming and outgoing trunk access? -- respectfully, Joseph ------=============

Hi, I am requesting for a E1 connection from my telco. They are asking if I want DSS1 or SS7, and I am stuck here. Could someone tell me the difference between the two? How should I decide which one to use? Thanks in advance for your help. Mark -------------- next part -------------- An HTML attachment was scrubbed... URL:

Does anyone know of a device that will take an SS7 link and convert it to a PRI? -- respectfully, Joseph - (606) 477-2355 x140 ------=============

I'm trying to upgrade from 1.4.24.1 to 1.6.0.9 with a TE120P card. I can't make any connection over the T1. From CLI: ERROR[26017]: chan_dahdi.c:14300 process_dahdi: Unknown signalling method 'pri_cpe' at line 37. cat chan_dahdi.conf cat chan_dahdi.conf [trunkgroups] [channels] language=en ;internationalprefix = 00 ;nationalprefix = 0 context=from-pstn switchtype=national

Hello. I am new to this forum. If this issue has been discussed already, please inform me, but my STFW have indicated that it has not. If SS7 were available on * would it make commercial sense to use it? There are case studies on the web (courtesy of the Death Star :->) for ISPs with 10,000+ subscriber lines showing clear cost savings in transitioning from PRI to SS7 controlled IMT. My

I have a customer installation with an Adtran DS3 mux. The DS1's go into my Asterisk servers that run IVR/Call recorders. The DS3 provider is Qwest, and they tell me that they routinely drop the DS3 service to redundant back-up's and that this is a common practice that happens thousands of times to DS3 lines daily across the US without any service interruptions. They say that the

Hi, I have setup 2 asterisk talking? a single mysql cluster. I'm also using realtime db. I've setup sip peering between the two asterisk servers. [asterisk-1] insecure=port,invite type=peer host=201.202.203.204 context=from-asterisk-1 [asterisk-2] insecure=port,invite type=peer host=201.202.203.205 context=from-asterisk-2 scenario: ext 100 registers on Asterisk 1 ext 200

Hello all, We are looking for some hardware requirements/recommendations to be able to handle a full DS3's worth of TDM -> VoIP traffic. The DS3 would bring 24 calls per T1 x 28 T1s = 672 simultaneous calls. We would then need to convert those calls into G729 SIP VoIP calls to send to our asterisk box over ethernet. Since everything is going in/out of asterisk is 729, and no features

Is anyone out there using Lucent brand equipment to handle an incomming DS3, converting all 672 calls to SIP (as G729) and sending those to Asterisk/SER over ethernet? If you are and are willing to speak to my boss about your experiences (over the phone) with it, please contact me off list. We have a possible contract with a local CLEC to handle their long distance, and they want to send to