similar to: OT ? Number portability, land line to Cell

At time to time I receive some junk faxes from some advertising companies that play smart and don't provide any TSI number so I can not bock them by the number in Hylafax. Despite calling their Fax Removal Service 1-800-... number several time they refuse to obey my request. So I would like to setup a small script or context loop in extension.conf if possible and maybe run it overnight; maybe

Any ideas on how asterisk could accept an email (such as an email to SMS or "number at mybox.org" sort of thing) and make a phone call to a specific number and make an announcement? I imagine the first part is the big question. joe a.

My Polycom phones are displaying time, off by one hour. Seems they are on the old DST rules. How do I fix this? joe a.

Currently the plan is to forward all PSTN calls on our 2 incoming PSTN lines & 2 remote toll free's via IAX2 to staff. 3 different delivery methods 1) Users local to the office where the lines come in with GS/PSTN phones 2) IAX2 to remote location * server then Cisco 7960 on that lan 3) IAX2 to remote softphone That assumes they are in the office though. Recently I've been out more

Getting "no service" display on aastra 480i. Sip debug shows an "unathorized" blub when the aastra tries to register. Some reading indicates that 1.4 firmware wants aastra.cfg and mac.cfg in /tftpboot/. There are none. Anyone have basic config files? Or can point me to a good link? All links I have tried, that purport to have config files, are either dead or error out.

I have an existing Hylafax system using a mainpine 4 port board, 4 POTS lines. Have a recently installed Asterisk system, with a dedicated T1 line. (Well, it's really a fonality system). What would I need to do, or where is the reading material, for what I need to do, to convert the Hylafax server to use the T1 line? Reliably. Preferably to use DID's as well. The current FAX works

In a system connected to a verizon T1, Digium TE411P (quad T1 echo cancellation), client is complaining it is "too quiet". The complaint regards calls over the T1, not in house SIP only calls. Their description indicates they want some earpiece feedback of themselves speaking. Also, they complain that it takes several seconds (3-4) for the other party to respond. That is kind of

What are peoples experience with the reliability of the TDM400p. Specifically in the 2 FXO, 2 FXS configuration, which is the 022 (?) model. Is this board prone to random failures? joe a.

I am having a problem detecting incoming FAX. TMD22p (tdm400p 2 fxo, 2fxs) As I understand it, I must have faxdetect = incoming to enable detection of the fax tone. Then, I must have a [fax] context to pickup the line and send it to whatever extension the FAX device is on. In my case, I ask it to answer immediately and do a distinctive ring (r3) to alert that is its a FAX call so no one picks

problem - occasional garbled calls, mostly remote users. T1 connected to PSTN, SIP over local LAN and internet to "remote users". NAT at local firewall and at remotes. There is no traffic shaping in place, no QoS. Most are Polycom phones, two Aastra's. Start with QoS on LAN switches? No 2x4's please, start with 1x4's. joe a.

I have an odd issue, where a polycom 601 stops ringing, or more properly, maybe, stops *being* rung, when a call comes in. Other phones/extensions, continue to work fine, they being run at the same time. My dial plan works fine (?) seems it will ring properly, right after a reboot. It works fine for outgoing calls at all times. Hints? joe a.

There was a discussion a while back about how to pass Calller ID, when forwarding, as either the calling number, or the forwarding number. Had something to do with "scams" IIRC, but could not find in browsing the archives. So, is it in the docs? Starting point or full tilt would be appreciated. joe a.

I need to ask, to refresh, is the aux power connector on the TDM400P card *only* to power the ringer on any analog phones/devices on the system? Can I still use this board, to "terminate" POTS lines and use all SIP Phones? Due to circumstances, I end up with a 1u server that has no aux power connectors available. I "have to" use this server, so am considering abandoning

Since the beginning (of my Asterisk life) I have an install that is, supposedly, set up for call waiting. Using a TDM400p, with FXO and FXS modules. On the Analog phones, I can hear the Incoming call (call waiting) tone, but the system does not respond to a "hook flash", to place the current call on hold and answer the incoming call. I have not attempted, nor research how/if this can

New system install. At what point, in bootup, should I be able to get a dial tone on the phone ports on a tdm400p? There are two fxo and two fxs ports. I know which to plug into <g>. At boot up, as soon as wctdm is loaded, all the ports "go green, yet I do not get a dial tone on the phone ports. I thought as long as zapata.conf is correct, the board should be

I have a working system with two fxo and two fxs channels. I recenlty got an IAX2 account I would like to use also. While I have gotten the IAX2 channel to "register", it remains non functional, as the incoming calls, go nowhere and the outgoing calls attempt to go out over the ZAP channel. I can see this, via the CLI, with debugs on. I strongly suspect this is a dial plan/config

Excuse me if I recently posted on this, but I cannot find it, in my, or the list archives. Is it possible, when transferring a call, to set the user ID to that of the "outgoing number" instead of the incoming number? I believe the answer is (was) yes. New twist, does it matter what the destination "media" is? Meaning, the call would be coming in on a T1, going out on a T1,

This is a follow up to an earlier post. Looking for a means to "individualize" incoming FAX, so as to distribute them to the intended recipient. While the PBX is based on Asterisk, it is not possible for me to "enter" the box to modify things, to any great degree. I thank those who mentioned IAXMODEM, earlier, but that seems a no go. Currently, there is a dedicated T1 into

On Wed, 2020-11-11 at 11:34 +0100, Thomas Bendler wrote: > Am Mi., 11. Nov. 2020 um 07:28 Uhr schrieb hw <hw at gc-24.de>: > > > [...] > > With this experience, these controllers are now deprecated. RAID > > controllers > > that can't rebuild an array after a disk has failed and has been replaced > > are virtually useless. > > [...] > >

Hey everybody, I wanted to know what other may be doing to stem the flood of inbound junk faxes? We currently using Asterisk/iaxmodem/Hylafax for fax services and get a number of junk faxes daily. Most (If not all) of them have caller-id blocked and have a TSI of "". I was hoping that, since we are using a PRI, there would be other information coming across that I could use to