similar to: DTMF detection problem on wctdm24xxp

Thanks to the great support at Rhino Equipment and Digium, this has finally been solved. I wanted to post the solution back to the list in case anyone else is having a similiar issue. I started by calling Rhino support so I could eliminate channel bank configuration as the issue. We were able to determine the channel bank and signalling were all working as expected. I then began to monitor

Hi, I'm running FC3 with kernel 2.6.11. All the binary files and zaptel kernel modules is not available to system at boot time. They are extracted in a ram disk at system startup and then zaptel modules are loaded manually and so on. I have no problem with this boot routine and i've been tested all digium cards (expect tdm24) and they work fine till now. The problem appeared when i

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules

The Asterisk Development Team is pleased to announce the first release of DAHDI-Linux 2.6.0 and DAHDI-Tools 2.6.0. 2.6.0 is a feature release which: - Adds support for the TE820 8-span card to the wct4xxp driver. - Decrease load time of analog cards supported by the wctdm24xxp driver. - Adds sysfs object model to facilitate persistent span numbering and early loading of modules

Good morning, I have a digium wctdm24xxp in my asterisk box, i am not able to see the callerid when the call is incoming from the fxo line, i live in Brazil, how can i change the signaling from fsk to dtmf? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi list, I'm having trouble with DTFM tones detection. Usually, some tones are being received duplicated in Asterisk, some not. As you can imagine, that's a very big problem involving IVR menu options, Meetme conferences protected with passwords, and so on. We are currently using DAHDi 2.2.0.2, module wct4xxp, which is managing a Digium TE220B card, with a hardware echo canceller

I'm trying to configure a TDM808P card on debian. When I modprobe wctdm24xxp i get this error FATAL: Module wctdm24xxp not found. FATAL: Error running install command for wctdm24xxp I think i have successfully compiled the zaptel drivers, and the card appears when i do a lspci 02:06.0 Ethernet controller: Digium, Inc. Unknown device 0800 (rev 11) Subsystem: Digium, Inc. Unknown

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

Hi, Before I report a bug on http://bugs.digium.com, I would like to know if someone is seeing the same error message. Personally I am not using wctdm24xxp but other modules such as wcte12xp and wctdm. The latter modules load fine and are compiled with pci_register_driver as expected. The only module that seems to require the deprecated function pci_module_init is wctdm24xxp. Is this normal?

Actually I am using Asterisk 1.2.7.1, zaptel 1.2.5, libpri 1.2.2 I ve tried many values for rx/txgain togeher with echocancel and relaxdtmf. The detection is not working with call file, manager originate and not with the dial command to the mobile. I have no ideas left. I got it sometimes to work if I use a specific channel (i.e. Dial(ZAP/14/...) But with the same vaules on a second call there

does * support call return? i want when the operator transfers a call if the transferee is busy or doesn't answer the call the call return back to operator again... this feature may be called: call return on busy call return on no answer Paradise Dove

Hi All, This is a request for testing for users of Asterisk 1.4 or 1.6 with any of the following Digium VoiceBus based cards: TDM2400P, AEX2400, AEX800, TDM800P, TDM410, TE120P, TE121, and/or TE122. From a practical standpoint, this branch should allow these boards to work in more systems / configurations where IRQ misses caused problems in the past. The updated wctdm24xxp and wcte12xp

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.3.0. DAHDI-Linux 2.3.0, DAHDI-Tools 2.3.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.3.0. DAHDI-Linux 2.3.0, DAHDI-Tools 2.3.0, and DAHDI-Linux-Complete are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0-rc1 DAHDI-Tools-v2.7.0-rc1 dahdi-linux-complete-2.7.0-rc1+2.7.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: *

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0-rc1 DAHDI-Tools-v2.7.0-rc1 dahdi-linux-complete-2.7.0-rc1+2.7.0-rc1 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: *

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0 DAHDI-Tools-v2.7.0 dahdi-linux-complete-2.7.0+2.7.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: * Driving closer

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.7.0 DAHDI-Tools-v2.7.0 dahdi-linux-complete-2.7.0+2.7.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In this release: * Driving closer

Hi, After some testing I've found out that my client's hardware recognizes DTMF only if digits are sent 50ms apart with 50ms of tone duration. This was tested using a test device which generates DTMF. Now asterisk doesn't do it by default because digits going out from Asterisk are not being recognized. Using command sendDTMF, I can control inter-digit duration, and using