similar to: Billion ISDN problem

Hi all, Can anybody tell me that wether I should install DIGIUM-TE120P card on redhat9.0 2.4.20-8 or 2.6.18 kernel. I am using kernel 2.6.18 but facing a very serious problem of modutils and iptable. Can anybody help me out. Thanx and Regards sanchal singh

Hi everyone! I'm quite a newbie at this Asterisk stuff so please bear with me. We've recently decided to start training in Asterisk via AsteriskNow! Asterisk version is 1.4.18.1 through AsteriskNow! 1.02 The box we have is paired with a Digium TE110P and we've managed to get it to the point where incoming calls via a single DID (from NTT Japan) can be received and answered

Hi, all I have installed TDM400 card. I can see it is there (lspci). But Asterisk does not find it. phonebox2*CLI> zap show status No Zaptel interface found. I assume that driver is not loaded, but I am sure I have installed it (I compiled zaptel and then re-build asterisk and did make install for both zaptel and asterisk). When asterisk is started I get: Jan 2 06:28:08 WARNING[3473]:

All of sudden my FXS module is not working. I have a TDM card with one FXS and one FXO, FXO module seems working fine. I also noticed the LED is not on for my FXS module while it is on for my FXO module. Sep 13 12:11:44 WARNING[9870]: chan_zap.c:887 zt_open: Unable to specify channel 1: No such device Sep 13 12:11:44 ERROR[9870]: chan_zap.c:6612 mkintf: Unable to open channel 1: No such device

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

Hello. I am new to Asterisk but I have been reading like for a month all de documentation and tutorials that i have found. Most of them from de voip-info.org. Recently I set up an Asterisk server based on Debian 'Sarge' 3.1. Everthing was looking fine. I even locate an old modem that would work like a X100P Clone (an Ambient MD3200) and after compiling and installing zaptel it is

I'm running Asterisk on a Gentoo box with the Zaptel 1.2.1 drivers. If I boot the machine without having the wcfxs module autoload, then install the module with modprobe, asterisk works just fine. If I boot the machine and autoload the wcfxs module, the module loads fine: > Jan 11 11:06:55 asterisk Zapata Telephony Interface Registered on major 196 > Jan 11 11:06:55 asterisk ACPI: PCI

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

Hi, I've a little problem with my asterisk server. I have managed an asterisk server for a few months one. Today, I wanted to restart it and when I did it, my asterisk server didn't want to start again. I looked at the various messages in /var/log and the same thing appears. " [chan_zap.so] => (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf': Found Sep 30

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

I have a new Sangoma A102 and I'm trying to get it running in asterisk. A look through the dmesg log shows the card is detected and the various channels created. However, when I start asterisk I get the error below. Any ideas? My zapata.conf is below. Thanks, MD == Registered custom function SIPCHANINFO == Registered custom function CHECKSIPDOMAIN == Manager registered action

Hi, I have two WCT100P cards installed on a suse 9.0 box. Installation for Zaptel complains of some unresolved dependencies. The zaptel and wct1xxp modules load without any errors. ztcfg give no problems. The problem is when I start asterisk I get the following error and asterisk shuts down

Greetings I was getting bad static crackle on a phone, so I reload from the latest CVS and did a make clean ; make install on zaptel, libpri and asterisk Now I get this error [chan_skinny.so] => (Skinny Client Control Protocol (Skinny)) May 28 13:59:42 WARNING[16384]: chan_skinny.c:2541 reload_config: Unable to get our IP address, Skinny disabled Urgent handler [chan_oss.so] => (OSS

After emerging some updates this morning asterisk 1.0.3 fails to start I get the following errors: ..Jan 6 00:39:24 WARNING[28998]: chan_zap.c:765 zt_open: Unable to specify channel 1: No such device or address Jan 6 00:39:24 ERROR[28998]: chan_zap.c:6197 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 Jan 6 00:39:24 ERROR[28998]:

Hello, This is debug output I get: Jul 28 15:05:49 WARNING[8249]: chan_oss.c:239 sound_thread: Read error on sound device: Resource temporarily unavailable [chan_zap.so] => (Zapata Telephony w/PRI) Jul 28 15:05:49 WARNING[8249]: chan_zap.c:924 zt_open: Unable to specify channel 1: No such device or address Jul 28 15:05:49 ERROR[8249]: chan_zap.c:6460 mkintf: Unable to open

I installed TDM400P and X100P pci cards in a system running mandrake 10.1 official, kernel 2.6.8.1-12mdksmp. I can compile zaptel, libpri, asterisk and modprobe (zaptel, wcfxs, wcfxo) without errors. Except that running ztcfg and asterisk fails. [root@asterisk asterisk]# ztcfg Notice: Configuration file is /etc/zaptel.conf line 3: Unable to open master device '/dev/zap/ctl'

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Dear All, I have the following entry in the /etc/asterisk/manager.conf file, [general] enabled = yes webenabled = yes port = 5038 bindaddr = 0.0.0.0 [admin] secret = admin read = system,call,log,verbose,command,agent,user,config write = system,call,log,verbose,command,agent,user,config When I did 'reload manager' in CLI I have received following error, [Nov 7 13:13:26]