similar to: Improve voice quality on Asterisk + chan_capi + DIVA BRI

I've got a brand new Eicon Diva Server BRI card and I want to configure it with Asterisk. I managed to get asterisk and zaptel to compile and install, I've compiled and installed the drivers for the Diva card and now I need to compile and install the chan_driver for chan_capi. Unfortunately this fails miserably. I get the following messages: I'm using: Kernel 2.6.16.37.4,

Hi list, Does chan_capi work with kernel 2.6? The Eicon Diva server card loads fine judging from /var/log/messages but Asterisk gives an error when trying to load the chan_capi module. I'm using chan_capi-0.3.5, zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a msg that may be related and don't know

Hello everyone. I need a BRI ISDN card that works in Romania. I already have one of the "Cologne HFC-S" PCI cards and it doesn't work right, it's junk. I get waaaay too much echo using it. I'm now "shopping" for a better card. Can anyone recommend me a card that "fits" the following: (a) Costs less then $1000 / 750 euro (b) Has one or (preferably) two

Hello, I have an issue getting the chan_capi module to load in asterisk cvs from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva Server Bri card. I load the modules with: modprobe -v divas divacapi I load the firmware with: divactrl load -c 1 -f ETSI -vd6 Output in /var/log/messages is: Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table (http://www.melware.net) Nov 9

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

I am trying to use chan_capi with an Eicon Diva Server BRI. I installed the Eicon drivers from source including CAPU and I can use the board correcly using tty_test and minicom over /dev/ttyds01 or /dev/ttyds01. I need to insmod capi ( why? it is not written anywhere) and then capiinfo shows me all board parameters, but I have to break it otherwise capiinfo doesn't exit at all, but I don't

Hi all, I have a Diva Server V-BRI-2 card, which support, as written in reference guide: Extended tone processing (human talker detection, generation and detection of country-specific tones) I would like to detect human speech and fax tone with asterisk. I think that the diva card transmit a DTMF code when detecting voice, but chan_capi doesn't receive this DTMF code. I verbose it

Hello all, I'm having problems getting chan_capi 0.3.5 to work well with an Eicon Diva Server card using using the driver from linux kernel both 2.6.10 and 2.6.12 (vanilla versions). I have a (really two) producci?n system(s) running chan_capi in another identical Eicon Card using kernel 2.4.27 and the Diva Server drivers from Eicon. I installed an compiled the source level rpm

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz

We are experiencing slightly distorted audio with playing of recordings on our Asterisk server when the call comes in over our Eicon Diva Server BRI card. An example is an incoming call to IVR and playing some of the standard Asterisk voice prompts. Note that there is no audio problem with internal access to the same recording. Neither is there a problem with calls not involving the playing of

Hi *, I want to integrate the Eicon Diva 4Bri Card to Asterisk. Eicon drivers and capi is installed. I use the latest dev version from eicon compiled and installed for my fedora 2 system. I found the chan_capi for asterisk from www.junghanns.net. Also loaded the patch and applied to the chan_capi source tree. I changed the Makefile to include the capi20.h from eicon:

Hello everyone: using chan_capi 0.7 and asterisk 1.4 Quick question: How can I detect the number of "voice" channels (B channels) in use at a given time. I'd like to call "Busy" if two B channels are used on my BRI to give the calling customer a Busy signal. Long question: On my single-line BRI (two channels) I'd like to give the 3rd simultaneous incoming call an

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hi Guys! I got a Diva passive ISDN card and I can't get it work with asterisk 1.4, It is supported in the kernel as an isdn4linux device but I can't find "Modem" channel type when i type in: core show channeltypes. I'm guessing it is removed in asterisk 1.4. Tried with capi interface but it does not work :( Anybody got some idea how can i make it work or got a link to a

Hello all, This afternoon I had a BRI line installed by Telstra (our telco in Australia). I'm using an Eicon Diva 2.02 PCI ISDN card with the isdn4linux driver. Incoming and outgoing calls with Asterisk work fine (and with no echo - my main reason for getting ISDN). However, I can't seem to get outgoing DTMF working (incoming works fine). I made a call from my desk phone (Cisco 7940G)

Hello, I need to connect one diva server 4bri to a portuguese BRI interface. The operator (PT) said that this bri is in point-to-multipoint mode (S0). Previously one PBX has connected to that interface. The asterisk and diva drivers are working ok but i cannot communicate to outside via this bri. Xlite gives me the message: "call failed: declined". Anyone have experience with this

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hi! I'm trying to enable echo cancelation with my Eicon Diva Server 4 Bri card. I've enabled it from zapata.conf, (as I read from www.voip-info.org) ------------------------------- ; Enable echo cancellation echocancel=64 echocancelwhenbridged=yes echotraining=2000 ---------------------------- but nothing seems to change, echo is still present. Any idea? Should I enable/change something

Hello Everyone, I am once again wondering about EICON. I have had no success with the Diva Pro or Diva Pro PCI, so my question is, does anyone use an Eicon Server BRI card on Asterisk? Or would I be better off trying to get a split PRI? Regards, Greg