similar to: Automatic Hang

Greetings to everybody. My question is that it?s impossible to pick up a call from ZAP, IAX or mISDN with my Ext Key of my GrandStream. It always give me a Spawn Message on CLI and a ?603? error on my LCD GrandStream. Exactly from my CLI screen i get this message -- Executing NoOp("SIP/11-096c2ac0", "Probando 1 ") in new stack -- Executing

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

Hi, I have switched a while back from chan_capi to chan_misdn. When the number is dialed and the phone is then picked up everything works just fine. Some users however FIRST pick up the phone and then start to dial... I did not get this to work with misdn. When two digits have been dialed, asterisk sees the extension as complete and does not wait for further digits. I am using an midsn NT

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

I realize I cannot use inband audio for phones (voicemail and internal ivr, password for external trunks and other thing not working) So I put everywhere rfc2833. Doing this, anyway, make any EXTERNAL IVR NOT working. I see a lot of posts about this, but no solution, becouse using inband audio (which works for outside...) breaks inside IVR Is it possible to define to use inband audio ONLY on

Hello everybody. I am trying to configure an Asterisk on Debian with the Billion ISDN card. I am using mISDN. But when I call on the CLI apears this: -- Executing Dial("SIP/101-081805b8", "mISDN/1/943833473|45|tTwW") in new stack -- Called 1/943833473 P[ 1] empty_chan_in_stack: cannot empty channel 255 P[ 1] --> we have already send Release_complete == Everyone is

Hi list, I've installed Asterisk 1.4.0 with newest mISDN 1.0.4 + mISDNuser 1.0.3 on Fedora Core 6. I get many compilation error on mISDN. It wants to include linux/config.h That I fixed by removing the #include line at every occurance. (Don't know if that was a wise move, but it then compiled). mISDNuser and asterisk compiled fine, and asterisk can find and use the ISDN BRI port in

Hello. I have a strange problem with the MeetMe application. Configured is a misdn msn to go into a preconfigured MeetMe room. exten => 12,1,MeetMe(1234,pIM) The first caller gets the prompt to enter the pin and then gets connected to the MeetMe room. The second caller gets also the prompt but after entering the right key he hears a dialtone followed by the message: The number you have

Hi, everybody: As part of a paging macro I'm using SendDTMF to send digits to the called party. The section looks like this: exten => s,1,Wait(0.5) exten => s,n,SendDTMF(9531290) exten => s,n,Wait(1.0) exten => s,n,Set(MACRO_RESULT=CONTINUE) To test I direct the call to a live extension just to hear what's happening -- what actually happens is that only the 9 is sent, and

I have been trying to figure a way to SendDTMF into a MeetMe room using the Manager API. I can't redirect everyone into another context and then bring them back because that would mess up my logic. I am trying to use local channels and the originate Action to accomplish this. Exten: 3441115 Priority: 1 ActionID: actid-00000001 Context: senddtmftones Action: Originate Channel:

You're quite right. We'll need to see your misdn.conf file to check the settings. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 13:49 -->> To: asterisk-users at lists.digium.com -->> Subject:

Hello, I am using macros to give the ability to a call-receiver to 'accept' a call. However, any keypress connects the caller. Anyone have any suggestions about how to re-engineer this so that the receiver can deny the call, or press other keys to do other actions, without connecting to the user? Thanks, Jason Wolfe

I've tried to transfer a call using the Flash command, but with my configuration it doesn't work. I have a traditional PBX connected with a zap channel to Asterisk that acts like an IVR: TELCO line --> traditional PBX (FXS) --> (FXO) Asterisk >From the TELCO line I can make a call to the traditional PBX and reach Asterisk, the IVR system on Asterisk answers the call and I can

I have a dialplan that requires that we use * to send the long distance access code to AT&T. I have found in the list that the `w` command can be used to inject a pause, I have tried the following: exten => _91NXXXXXXXXX,1,Dial(ZAP/g1/${EXTEN}www5555555,70) There `5555555` is the ld access code. I tried various quantities of `w`s but I never got * to dial the ld access code. Allof the

This 2 line code is doing what I wanted. exten => 200,1,voicemail(200) exten => 200,2,Hangup What I've been told is that they want the 20 year old phone system to light up the message bulb. (yea, a filament bulb, not an LED) To do this you pick up on the line that goes into Asterisk and do a: exten => 200,1,SendDTMF(200w#86) But I don't know the path to take to get that

I am trying to send 'codes' over an isdn2 link - such as *#24# - to activate call forwarding. But it doesn't work. I have tried sending it as a straight dial, and also as a DTMF string...but no luck... I spoke to a telco tech and he said I had to send a facility code....huh? Anyone with any ideas on this one? PaulH

Greetings. I am attempting to configure a system based on Asterisk 1.2.3 to be used as a backup should our aging voice mail/auto attendant system fail, which seems increasingly likely given its advanced years. The first part of this task is getting the auto attendant feature to work correctly, which I would have figured to be relatively easy. I have successfully built a menu structure, but cannot

List, Having a little trouble with the following. Let me prefix by saying I have blind transfers working from the following setup. Inbound call [from-zap] (SIP/sv0071iv) answers. Zaptel -> Asterisk -> SIP extension SIP extension then blind transfers [from-sip] --- SIP extension -> Asterisk -> Zaptel During this whole process, the original channel off the trunk (lineside T1) is