similar to: Purposely setting red alarm on PRI for testing purposes

Can anyone offer up a suggestion on a reliable and cost effective customer premise hardware setup to be able to take an inbound IP T1 and deliver a PRI interface to a remote office? Trying to reduce the amount of hardware required to implement this, right now we use a Cisco router to take the IP T1 in on a serial port and then we go Ethernet to a slimmed asterisk box with a single port T1

Hello All, I was wondering if I could do the following on asterisk... Get a T1 between 2 locations, and split it into a data channel of like 1024, and use the rest for voice channels. Has anyone done this and had it working well? Or would I need to get a csu that allows a split into two interfaces? Regards, Greg

Management just approved purchase of a Digium T100P and a T1 card for our Merlin Legend Switch. I will appreciate comments from anyone performing this installation before: - Which T1 card did you use in the Merlin Legend? - Did you require any special interface? (CSU/DSU, etc) - Any items to watch during installation. Also we will need to remove one of our old analog Trunk cards to accomodate

Hi all, When configuring Asterisk with an ISDN card, it will at one point become necessary to select the LBO (Line Build-Out) value. This is an integer (0-7) that is determined by the length of the cable and is selected from the following table. Many of us are familiar with it: CSU (dB) DSX-1 (feet) ------------------------------- 0 0 0?133 1

Hi, I learned about shorewall a few days ago and am quite impressed with how easy it was to create a powerful firewall. I set up a test system with a cable modem and it worked flawlessly. I''m going to be building a Router/Firewall for a new T1 that will be using a Sangoma WANpipe card w/ integrated CSU/DSU to connect to a T1. Has anybody done this yet, or do you know if it''s

I have a machine in my office, it is labelled Cable and Wireless, and on the back it says, SMarT-1 I have searched the web, and no joy. It connects to a PC via a serial cable, has anyone heard of such a device? -- ***** Not everyone is touched by an Angel.... .... Those that are, never forget the experience *****

Hi, I have 2 servers: one is running 2 B410P cards with 8 euroisdn lines (mISDN) connected on it, everything runs fine. I prepare a new server - HP 360 G8- with 2 HA8 cards each of them 1 module of 4 lines. Already had with this machine an RMA on both cards as they was faulty and crashed the server. What happends is that when I connect cables on the HA8 modules (those cables are unpluged

In an effert move my Dmz from a snapqear roouter to Linux with shorewall. Question is I have network 64.42.53.200/29 which makes default gw 64.42.53.201 network 64.42.53.200 broadcast 64.42.53.207 mask 255.255.255.248 and I want to set up shorewall with eth0 64.42.53.202 eth1 local eth2 dmz where dmz will use say 64.42.53.203 for web and email server. Where I do not need or should I say use

Hello, I am currently pricing out various T1 and PRI options for a client of mine. We need voice and data - we want T's. Whether it be two seperate T's, two superate fractional T's, or one combined fractional T, we need it done. We are getting pricing and one provider is telling us that they have quality issues with the "Integrated Access" product. From what they

[Please excuse if this is a repeat; I initially tried to send it from a different account, and it's been held up for a couple of days awaiting moderation.] 1) What's the absolute minimum required (hardware-wise) in order to get one in-bound POTS line into Asterisk, and then have IP phones "inside?" [In other words, I obviously need a NIC -- but what would be the

Hi, I'm trying to put together an * system with extremely high up time. The system as it stands now is 1 dual p4 with raid, redundant power, etc.. and a T100P card. I would like to get a second similar or identical box with another T100P card. I have 1 PRI, how do I get the second box to take over communication with the PRI should the first box fail? Of course I'd like this to be

Hello All, I have a Digium Wildcard TE410P Quad-Span T1 Card, when I do connect T1 lines it goes in RED. When I do connect the same line on a different Server (Same Model T1 Card) it works fine. How do I examine/diagnose my T1 Card for any hardware failures. I heard about loopback test , how helpful it is? Here are my configuration /etc/zaptel.conf span=1,1,0,esf,b8zs

Do the Digium cards have a built in CSU? Is a CSU an FCC requirement? or just a carrier requirement? TIA

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

Hi, I have this Samba file server, that indeed is a client of a Windows 2000 Server PDC. I am the Samba machine admin, but not the Windows one. I have to join the Samba machine to the PDC on the 2000 server. I ask the Windows 2000 server admin to come to my Samba machine and insert his login and password to join my machine, but i always get the same error (after my signature). The Windows

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Hi, I know that there was a jitter buffer patch (for sip) for the 1.0.9 branch some time agin. At this time, we can not upgrade to 1.4.x. Is there a useable, fairly stable INCOMING sip jitter buffer patch? That is.. I want Asterisk to jitter buffer incoming SIP packets. -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a dataset, which contains a day column that I would like to retrieve results on. Is there any reason why daily_stats.where(''day = Date(?)'', dte).first returns and empty set, daily_stats.find(:first, :conditions => [''date(day) = ?'', dte]) returns the correct data and daily_stats.where({:created_at => (date.midnight - 1.day)..date.midnight}).first

Need help...I need to install a card to terminate 7 lines...I have not order the phone lines yet...I can either do analog lines 1FBs or order a fractional T1...any suggestions on what hardware would be easier to install and configure...also if I went with a T1...do I need an external CSU/DSU or anything or does it just plug into the T1 card...thanks.. -----Original Message----- From:

Hi Im trying to install my TC400B trans coder card when I do: modprobe wctc4xxp tail -f /var/log/messages says: May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Encoder' with 92 transcoders (srcs=0000000c, dsts=00000101) May 13 14:56:36 pbx2 kernel: Registered codec translator 'DTE Decoder' with 92 transcoders (srcs=00000101, dsts=0000000c) May 13 14:56:36 pbx2