similar to: T400P 4 Port T1 Cards for Sale

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Hi, I've posted this question on OpenSS7 mailing list but I didn't get a clear answer. I have a system running asterisk using Digium T400P card. Can this same card be used with OpenSS7 project to carry SS7 links? Is there any difference between these two cards? -- Matteo D'Amato Network/Telecom Administrator Intelco Communication Inc

Anyone care to elaborate on the differences between the T400P and the TE405P? -Darren -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050908/e817f8bb/attachment.htm

Can T400P be configured for nfas (one d-channel providing signaling for more than one span)? Thank you. Alex Zarubin -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030522/f2b637a9/attachment.htm

Another issue to consider is T1 framing. If your application is putting bits onto the T1 at the rate of 1.544 Mbit/s then the T1 would need to be unframed. I don't believe this is an option in zaptel! If however, it is putting bits on at a rate of 1.536 Mbit/s and adding 8000 bit/s for framing then you may be able use the suggestion below. Don Pobanz On Thursday, April 03, 2003 3:28 PM,

Could anyone with any experience with * over a non-PRI T1 help this newbie? I have a fractional T1 that is working fine through a channel bank, but I can't get any response on * using a T400P. My analog line and the extensions work fine, but the T400P port 1 shows a red led (what exactly does that tell me?). I brought up zttool which shows a condition red also, but ztcfg shows nothing amiss.

I'm having (I think) timing issues in relation to bridged T1-T1 calls via dynamic spans. Fax calls are intermittently working, but voice is fine. My box has a Sangoma A400 inside it as the primary Zaptel timing source. My T1 PRIs that are hooked to the box come in via a foneBRIDGE2 (dynamic TDMoE spans). PRI #1 is the telco and PRI #2 is an existing Comdial FX-II. For some reason, bridged TDM

Since i'm sure there are others out there in the same position as me, being disappointed that the original T400P and E400P cards are no longer available from Digium, I thought I would pass on a place I found to get them. I needed the older card, since I didn't want to have to get a motherboard with 3.3v pci slots on it.

Hi, We are trying to validate Asterisk as a media gateway PRI <-> SIP with two T400P (8 T1s) per box. The first experience with BOX1 (Compaq, 2.53 GHz, 1 Gb RAM) and just one T400P was encouraging - on the load test with 3 T1s worth of calls we had on average 75% idle CPU. Not so with BOX2 (Dell, single 2.6 GHz Xeon, 1 Gb RAM, 2 T400P) and BOX3 (Dell, dual 2.6 GHz Xeon, 2 Gb RAM, 2 T400P,

Hello, I'm preparing a setup before installing it within the next few days. In this setup, I'm using a SPA112 as an ATA for an analog phone. The target phone is a Gigaset A400 DECT handset. In my lab, I've got another A400 handset and an old Matracom 46 handset. When I connect my Matracom 46 handset to my SPA112, I can send and receive calls. When I connect my A400 handset to the

I'm trying to hook up a non-PRI fractional T1 using a T400P port. The Telco says that it is provisioned as AMI with SF (not ESF) and that they are signalling by "sending down a straight DS1" (I'm not sure what exactly that means). They are also sending DNIS over these channels. I currently run it through a channel bank for my IVR application and it works fine but I am now

I have a T1 PRI from the telco and have been trying to get it to work with the wildcard T400P. I know framing and coding is esf and b8zs. what else should I be putting into the zaptel.conf and zapata.conf. Dave Anderson

Hi, is there anyone who have experience with more as one card in one machine ? Or, somebody from the Digium team who can make an assertion about this ? Regards, Thomas.

Another nibbage question: modprobe tor2 -v install /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg insmod /lib/modules/2.6.5-1.358smp/misc/tor2.ko ZT_SPANCONFIG failed on span 1: No such device or address (6) FATAL: Error running install command for tor2 dmesg states that the module is registered however. Am I doing something seriously wrong? I have my zaptel.conf configured as

Hi, I'm looking into support for SS7 and I found an article (http://www.openss7.com/news13022002.html) which says that OpenSS7 supports Linux Support Inc's T400P-SS7 Quad T1 and E400P-SS7 Quad E1 PCI interface cards. It also says that Linux Support Inc is the primary sponsor of Asterisk. However I cannot find these cards on the Asterisk hardware page

We have (10) Dialogic D/240SC-T1 REV 2 voice boards. Prefer single buyer, take all (10) for $675/ea Cory Andrews ***************** b2 Technologies 454 Sonwill Drive Buffalo, NY 14225 ***************** voice: 866-44-B2TECH X22 fax: 716.630.1548 email: sales@b2llc.com

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

Modem connect speeds on calls through * seem to be lower than calls made through the telephone company lines or our old Rolm PBX. All data calls have 2 wire analog modems on both ends. For my set up I have channels of a Zhone channel bank tied to 2 modems. The Zhone channel bank interfaces my * server with a T400P card. modem --- Zhone Channel bank - * via T400P card - Zhone channel bank -

Hi list, I'm having problems transferring certain calls made by the attendant between the PSTN and to an internal extension. Although, transfers between the majority of the calls ends successfully. Debugin this, I've found that calls made to certain "numbers" (Telephony Providers), aren't detected as ANSWERED in the CDR, so they are not properly accounted (for billing),