similar to: SER vs Asterisk?

Hi guys, I've setup on box with a TE110P and time to time I need to access remote equipment outside of our office and use a data channel. I'm wondering if do I need to buy a POTS line only for this time to time acess or what's the easiest way to do that via my TE110P on asterisk box. I know that is possible data transmission with this Digium Card, I'm wondering how... Any tip any

Dear all, I've a live system that needs to be upgraded but, before I proceed to the upgrade I want to assure the rollback process. That's why I'm requesting your feedback, in fact this asterisk in live system isn't going so bad but.... the upgrade is essential NOTICE that the upgrade will keep the same version 1.2 not from 1.2 to 1.4 Requirements: -backup /usr/sbin/asterisk

Hi List; Is Digium the best telephony cards to be used with Asterisk? The prices are some how high, any suggestion? Regards Bilal ____________________________________________________________________________________ Never miss a thing. Make Yahoo your home page. http://www.yahoo.com/r/hs

I just read on Slashdot (at http://yro.slashdot.org/article.pl?sid=07/12/16/222243 ) that Trixbox "has been phoning home with statistics about their installations", as a Trixbox user exposed in "Trixbox Phones Home" at http://www.trixbox.org/forums/trixbox-forums/open-discussion/trixbox-phones-home . -- (C) Matthew Rubenstein

Hello I want to use Asterisk to implement a SIP Domain allowing my clients to do URI dialing and receive calls from the Internet through URIs and ENUM. My question is, should I put my Asterisk outside the firewall (in the DMZ) to allow connections to the Internet? Or should I have it inside my local network and put a SIP Proxy (like Openser) in the DMZ to implement the SIP domain? Thanks

Hi, I am trying to implement call forwarding on the event that my ATA was not reachable to Asterisk, whether due to registration timeout, network interruptions between the ATA and Asterisk, or simply because the network on which the ATA resides in unreachable for any reason. I there a way of implementing such a feature in Asterisk? I have implemented CF unconditional, and CF on busy, CF on

Hi @ all, i set a server to a costumer of mine with a TE207P for use with 2 E1 Lines. I set them together into one group in zaptel/zapata.conf The point is now, the customer has a free-volumina of 60k minutes per month, per line. How can i make a kind of load balancing, that both lines will be trafficed the same way ? I read something about DIAL(Zap/r1/.) for using round robin, and

Hello. I am going through the documentation and trying to find if asterisk can help me in my case. It is quite difficult to find answer because I do not know the exact question. I have two location. Each in different country. Both locations have Siemens HiPath - different type and software. I can not use card that would allow me to connect those PBXs using SIP. But I have some free ISDN and

Good Day all Please I am having some issues on my voip asterisk server I make internal calls on extensions configured ie extension 192 can call extension 195 etc But each time i try to make calls outside the extension ie calling a GSM or an external line ,i always hear this response "all trunk calls are busy please try your call again later" Please how can i resolve this problem . I

Hello, How can I make a live chat (mainly text, but with voice/video chat if possible) interacting with asterisk? Can asterisk control simultaneously the queue between people calling by phone and people by web chat? At my work, there is a call center using asterisk to control the queue of the clients (by phone) already. This part is ok. But now I need to make a chat room at the website

I have an existing Hylafax system using a mainpine 4 port board, 4 POTS lines. Have a recently installed Asterisk system, with a dedicated T1 line. (Well, it's really a fonality system). What would I need to do, or where is the reading material, for what I need to do, to convert the Hylafax server to use the T1 line? Reliably. Preferably to use DID's as well. The current FAX works

Hello all, this is not really an * question but it is somehow related, i am trying to develop a working proposal for cheap and quick telephony services using Voip running over *. By running a wireless network (over 802.11 a/b/g devices), i plan to be able to reach customers directly with eithe table top or handheld 802.11 sip enabled phones. But the disadvantage is that how do i power each radio

Hi, I'm deploying a SER + Asterisk architecture, where SER is used as SIP registrar, and Asterisk is used for voicemail and PSTN gateway. This system is already able to make Call Transfers (Blind and Attended) internally between phones registered in SER, although, I can't make Call Transfers in some scenarios involving PSTN numbers (which need to pass through Asterisk). The problem

Hi all, i have the following setup PSTN -> routing server (asterisk 1.6.2.11) -> IAX -> callcenter asterisk 1.6.2.9 -> SIP -> agent Does work quit fine - then agent does have the abibility to transfer a call to a third party - the agent can initiate the transfer over a web interface - it does generate a asterisk manager atxfer request... So agent does initiate transfer - call

HI all: Iam planning to use my asterisk box as callcenter?,any one can advice me with the best callcenter open source program based on asterisk . ? Any help will be apreciated. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100307/116f1b75/attachment.htm

Hi, I have a server with 2 TE110P cards. 1 card is plugged to telco line, another card is plugged with a Hicom PBX. I want to send some call to VoIP phones and all other to my PBX. I don't known how to make my dialplan : ===========Extensions.conf========== [incoming_call] exten => 090200000,1,Goto(callcenter,100,1) exten => 022956353,1,Goto(callcenter,100,1) exten =>

Guys. How do those callcenter apps work with Asterisk where a call comes in and * send a URL and some screen popup up based on callerid or something or username or id and shows all the customers info? Anybody done that? What do you need to do that? If you are using ATAs or IP Phones, how do those integrate with the PC so the screen would popup?

Hello We are developing an application to be deployed on E1 lines (inbound and outbound calls) What is the best way to fully test the application if we do not have E1 lines in the development environment? Is there some kind of software tester to test IVR/Callcenter applications virtually?? thanks and best regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

---------- Forwarded message ---------- From: Marco Mouta <marco.mouta@gmail.com> Date: Feb 15, 2006 1:58 PM Subject: Which ATA device do you recommend? To: asterisk-users-request@lists.digium.com Hello, I'm developing a Voip Solution for a client, which ATA SIP do you recommend? there are some ATA devices fully tested with Asterisk? I hope that Asterisk experient users could give me

Sds, Paulo Henrique Cardoso Administrador de Redes - T.I. NHS Sistemas Eletr?nicos Ltda Av. Juscelino Kubitschek de Oliveira, 5270 Cidade Industrial, Curitiba - PR Fone/Fax: (41) 2141-9246/9247 www.nhs.com.br IMPORTANTE: Esta mensagem, incluindo quaisquer anexos, ? endere?ada exclusivamente ao seu destinat?rio e poder? conter informa??es confidenciais. A revis?o, distribui??o,