similar to: Re: asterisk-users Digest, Vol 32, Issue 67

Hi List, I'm trying to connect Asterisk with a Nortel Meridian using an E1 with MRFR2 signaling. I've connected both cards, and compiled all the required software... The problem is every call (outgoing or incoming) got dropped, complaining about some "T1 timed out" Only for testing purposes I'm using an application called testcall included on the lib-unicall package, and

Hi all I have MFCR2 successfully installed but seems to get warnings a s seen below when I start asterisk. Am running on Redhat 9. Asterisk Ready. *CLI> Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 far_unblocking_expired Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 local_unblocking_expired Dec 20 08:40:38

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I have a astunicall-1.4 setup with a te110p to a nortel pbx in Mexico. (Hate R2!). This is what I get when trying to call to * box using testcall: ./testcall Chan 31, class 'mfcr2', variant 'mx,20,4', end 0, caller 0, from '' to '' Loading protocol mfcr2 Thread for channel 0 MFC/R2 Chan 31: Call control(9) MFC/R2

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia (north africa). I have configure my MFCR2 according argentina R2 settigs : the test call run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2. generally in the begging no errors occur. after

Hello All I'm using asterisk 1.1.X and MFCR2 lib version 0.03pre2. when i call to E1 (connected with asterisk), chan_unicall don't detected event incoming call and show error. error messages: *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2

Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of

Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line

Hello , Thursday, June 14, 2007, 4:00:37 AM, you wrote: > Message: 2 > Date: Wed, 13 Jun 2007 09:40:08 -0600 > From: Anthony Francis <anthonyf@rockynet.com> > Subject: [asterisk-users] Weird sip registration problem > To: Asterisk Users Mailing List - Non-Commercial Discussion > <asterisk-users@lists.digium.com> > Message-ID:

hi, I am using debian 4.0 with version 2.6.18-4-686 I have downloaded the required files form site asterisk-1.2.24.tar.gz libmfcr2-0.0.3-1.4.tar.bz2 libsupertone-0.0.2.tar.gz libunicall-0.0.3-1.4.tar.bz2 spandsp-20060903.tar.gz I downloaded and installed the files in the follwing sequence spandsp libsupertone libunicall Till here it is compiling and copying

Hi, downloaded the latest snapshot just right now at soft-switch for MFC/R2 support and I get this message when trying to do libmfcr2; any idea ? it looks like he's not reaching Unicall. Thanks, Fred # make make all-am make[1]: Entering directory `/usr/src/libmfcr2-0.0.3' if /bin/sh ./libtool --tag=CC --mode=compile gcc -DHAVE_CONFIG_H -I. -I. -I. -I/usr/include/libxml2 -g -O2 -MT

Hi all, I have begun the release of my MFC/R2 protocol software. At http://www.opencall.org/installing-mfcr2.html there are instructions for installing what I have released so far. This is the MFC/R2 protocol software, and a test program. The software to interface Asterisk to the MFC/R2 code will be released shortly. It used to work, but it hasn't been touched for a while, and Asterisk

# ./testcall testcall.conf Chan 1, class 'mfcr2', variant 'ar,10,4', end 1, caller 0, from '30025860' to '013331339767' Chan 2, class 'mfcr2', variant 'ar,10,4', end 1, caller 0, from '30025861' to '013331339768' Chan 3, class 'mfcr2', variant 'ar,10,4', end 1, caller 0, from '30025862' to

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2

I followed the how-to for R2 that coppice wrote on the webpage http://www.opencall.org/installing-mfcr2.html, now asterisk has channel unicall and when i test an incoming call I get the following errors. astbox:~/mediatel/libmfcr2-0.0.1# asterisk -r Asterisk 1.0.0, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com>

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

If I make a call to asterisk's r2 E1 I get these errors *CLI> Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x1 [1/ 1/ 0/ 0] Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Detected Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Making a new call with CRN

Hello I'm using mfcr2 support (unicall) in asterisk 1.4. Everything is working fine, asterisk can answer calls. But after some random period of time mfcr2 module stuck. When I make a call to my * box I can hear only signal of getting caller ID ("tritirirti" - like jumping on :) ) and connection is terminated by my telecom operator. When everything I ok after few seconds of this