similar to: Not registering Port with VSP

All, I'm hoping someone can direct me as to why when someone calls my DID Asterisk tries to authenticate the incoming call on my outbound context. If I remove the GoTalk context I can receive incoming calls. Outbound calls work fine while I have the GoTalk context in place. The error I am getting when someone calls the DID is WARNING[16072]: chan_sip.c:8272 check_auth: username mismatch,

Hi All, I seem to be having a problem with all my VSPs. When I am registering with them I don't seem to be passing my port number. This problem causes other users the inability to call my VoIP number with the VSP. My VSP showed me what they are seeing. I have changed my useragent to be: Linksys/SPA941-4.1.15 Linksys/SPA941-4.1.15 Contact sip:1234321234@aa.bb.cc.dd with no

Hi All, I think I have missed something as I am resisted with 4 VSPs and I can not dial in using any one of them using the corresponding VoIP numbers assigned with the VSP. I can make outbound calls to another VoIP number to the same provider. The weird thing is that I have a DID with a VSP and I have that working fine but try using the associate VoIP number and nothing happens. When

Has anyone tried using BroadVoice for VSP? I have Asterisk configured for a home office & I've been trying to decide which VoIP provider to go with for a little while now. I had heard you could get sub $.01 calls but I have not found that to be true yet (not saying it's not possible, I just haven't found it!). Also I'm not sure if BV will support multiple lines. Any

I'm sure this might not be the correct place to ask and I have done a Google but I can't seem to find anything that says there is a VSP that will work with * in the Ukraine. I have a friend that lives in Kiev and basically want a phone number there to be able to talk to him and have him call me. If anyone has any information on it and they are willing to share please advise.

I have a list of VSPs that I use. Some are not able to terminate to different locations. It appears they are returning this error message: Sep 13 00:01:43 WARNING[22093]: chan_iax2.c:6835 socket_read: Call rejected by x.x.x.x: No such context/extension I would like to find out what the dialstatus is on this so I can try a different VSP that is able to terminate the call. Right now I have this

Bear with me this is a bit long winded. I am having some issues making automated outbound calls over Broadvoice from my Asterisk 1.4.2 server. For reference, none of the below issues happen when I make the calls to VoIP phones attached to the Asterisk server. What I am trying to do is call, using a .call file, out via the SIP trunk we have setup, and when the party picks up use AMD to

On Thu, Feb 13, 2014 at 5:52 PM, Renato Golin <renato.golin at linaro.org> wrote: > On 13 February 2014 13:47, Evgeniy Stepanov <eugenis at google.com> wrote: >> Hm, I see that -funwind-tables on arm-linux-androideabi target >> replaces this "cantunwind" with a proper unwind table. >> Hence http://llvm-reviews.chandlerc.com/D2762. > > If Android is

Due to an issue I'm having with 7.x, and trying to track it down, I spent tonight getting my server setup to allow my to break into the debugger when it hangs, and hopefully dump core ... But, although I *think* I've got it all, I'm obviously missing something, as it isn't breaking ... First ... I'm running a proliant server, and when I connect via SSH to ILO on that

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

Hi All, I have installed Asterisk 1.4.2 and have loaded ztdummy as I have no Digium cards. The problem I have is that MOH will not play. It starts and then stops. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 ZTDUMMY/1 1 UNCONFIGUR 0 0 0 I'm not sure if the above is correct.

I am trying to build cross compiler for custom processor (say XYZ) but on compilation it is giving error llvm-build: error: invalid native target: XYZ (not in project) I have tried configuring like these 1. ./configure --target=XYZ 2. ./configure --target=XYZ --enable-targets=XYZ 3. ./configure --enable-targets=XYZ But every time it is not recognising the XYZ processor. What could be the

Hi all, I've just been told from an ex workmate that my VSP (who I used to work for) has put an anti flooding limit of 80 SIP messages per IP per minute in place. I run the phone system for a facility that has a lot of extensions, but would rarely have more than 4 or 5 simultaneous external calls. Am I in danger of tripping over this limit? It sounds dangerously low to me.

Is it possible to display the incoming calling number on a handset when trying to pick up a call from another handset? I currently have Call Pickup working using *8, I have also used the PickUp application successfully but I'm not sure how to use these features so the handsets show the incoming calling number and not the number that you have dialled to pick up the call. Regards David

Hi, I am trying to do my first puppet configuration, already installed the puppetserver and client, in this link show my configuration and my puppet structure: http://paste.pocoo.org/show/212227/ But when i run the client side daemon i get this message: info: /Class[main]/Node[basenode]/Class[inittab]/File[inittab]/source: No specified sources exist err:

Dear All, I like to simulate a physiologically based pharmacokinetics model using R but am having a problem with the daspk routine. The same problem has been implemented in Berkeley madonna and Winbugs so that I know that it is working. However, with daspk it is not, and the numbers are everywhere! Please see the following and let me know if I am missing something... Thanks a lot in advance,

Hello List, This is what I want to do: When a call comes in I want to ring an extension that happens to be loud speaker. The users can the press *8 to answer the call. Is there a SIP device that I can connect to Asterisk as an extension that can accomplish something like this? -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP

Greg, Chris, and Jay, Thanks! You've given me plenty of info to digest. I really appreciate the responses. Apologies if my list manners aren't up to snuff! Thanks again, Jason

You need to add your target to autoconf/configure.ac. Here are the directions from http://llvm.org/docs/WritingAnLLVMBackend.html To get LLVM to actually build and link your target, you need to add it to the TARGETS_TO_BUILD variable. To do this, you modify the configure script to know about your target when parsing the --enable-targets option. Search the configure script for TARGETS_TO_BUILD,