similar to: Asterisk and DTMF

Hi, anyone can confirm if the Linksys's ATA and Router (PAP2-NA and RT31P2-NA) have the same limitation of just one G.729 call like the Cisco ATA 186 ? I'm testing both appliances here and found this issue but could not confirm this anywhere (nothing on the manual, no document or post from any user about this). In my tests they use G.729 only on the first call and G.711 on the

Hi list. I was googling about this subject and found a message to this list asking the same thing I want, but see no response. So, I'm reposting it in case someone has a solution for this. I'd like to know if there's some way to "detect" (not block) a collect call in a ISDN E1? I need this cause I have my own billing system and I need to charge my customers for collect calls

Hi, I have 3 PAP2 connected to *, they work fine but there are some things which I would like to improve, some of them are: - double ring tone when placing a call (I hear two tones it seems like the PAP2 is generating it's own tone) - some kind of noise (like glitches or something) when I pick up the phone (seems like some polarity thing) - I'd like to keep the tone after

The best I can do so far (which appears to be a bit of a hack) is (<:0>S0), which says to add a '0' to the start of the string and dial immediately. This gives asterisk an extension dialled of '0', which isn't the 's' that i'd hoped for, but is a good start! (S0) by itself doesn't work, nor does (<:>S0). Any other suggestions? Thanks James >

I have a Linksys PAP2. Identical setups for the two channels in both the unit and in Asterisk. In particular, both channels enable g729 and set it as the preferred codec, and have disallow=all and allow=g729 in sip.conf. If we make a call on one channel, it works (and uses g729), but if we make a call on the other channel when the first one is still connected, it fails. We have three g729

I have a whole bunch of remote devices connected to my Asterisk box, including SPA-3000s, PAP2-NAs and Cisco 7960s. The PAP2-NAs I have only rolled out recently and I am having a problem that is intermittent and inconsistent. It happens to some users but not other users on the same ISP. It happens to users in 2 different countries where the Internet setup (NAT issues) are completely different. It

hi all, just wondering what's happening here: i have a pap2 and an spa941. everytime i call my spa from my pap2 i can see it being added dynamically on the regcontext: [Oct 7 11:59:08] -- Saved useragent "Linksys/SPA942-5.2.8" for peer 100100 [Oct 7 11:59:08] -- Added extension '100100' priority 1 to sipregcontext but from spa to pap2 i dont see it, i looked

Hi i am using pap2 phone adaptors as clients to connect to asterisk server i am able to make calls but i cannot access voice mail using phone or start recording while call is in progress and when i place a call to local sip extension there is a long pause ( 15 sec ) before the call gets dialled i assume that the problem would be due to the dial plan in PAP2 if so please help me changing it

Is there a way to configure the linksys pap2 to automatically connect to asterisk on lifting the handset (presumably into the 's' state)? Asterisk would then be listening for DTMF tones to figure out what to do rather than having to put a dial plan into each pap2. I think the pap2 is pretty much the same inside as a few of the sipura boxes so the same thing might work if anyone knows...

In my seemingly endless search for the cause of echo on my SPA3000, I wired it up in the following configuration: Analogue Handset <--> (FXS)SPA3000(FXO) <--> PAP2 And set the Line1 dialplan on the SPA3k to '(<:@gw0>S0)' which means that as soon as I pick up the handset I get linked straight through to the PAP2, which gives me dialtone. Even in this configuration, with

Im a 3-days-asterisk-newbie. In 3 weeks, I must have a PBX installed in a new office of ours: Panasonic or Asterisk. Asterisk would be, if I can emulate some Panasonic functions on Asterisk fast, to convince the executives. What I have done until now: Bought 1 Linksys pap2 (2 FXS), 1 Linksys SPA3102 (1 FXS + 1 FXO) for making asterisk tests. Configured Asterisk/Fedora 9 so I can make SIP->PSTN

Hi I have installed CentOS 5 on my computer which has an Intel ICH5 sound chip. The card appears as it should, and I can adjust the volume just fine. However, when I try to play a sound file(.ogg for instance), rhythmbox plays through the file, but no sound is heard. I've tried as root, and I've tried doing cat /dev/urandom > /dev/dsp, and it's all quiet. Output from lspci:

Hi, I have a problem I will describe. I have PAP2 connected to the internet to an asterisk box with 2 TDM cards, one TE100P E1 with PRI and one TDM400P with 2 FXS an one FXO. When I call to the TDM400 cards from the PAP2 eveything is OK, sound quality is perfect. When I call to terminate the call in PSTN through E100P I hear clicks which aparently are RTP packet looses. This clicks are only heard

Hello, I have a Dell PowerEdge 2850 that periodically (6 times in the last 24 hours) freezes, requiring a power cycle in order to come back. The machine is running a Xen 2.0 stable source install. Here is the appropriate Grub entry: title Xen 2.0 / XenLinux 2.6 kernel /boot/xen-2.0.gz dom0_mem=131072 module /boot/vmlinuz-2.6-xen0 root=/dev/sda1 ro console=tty0 Dom0 boots happily, and new

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

I am using my first PAP2 device from linksys. Used many polycom phones... I configured the PAP2 device with asterisk. I have the registration, thought I was good to go. Plugged in my Valcom 2924 public address analog connection, called the extension and I got busy... very strange I thought. I then looked at the status page of the PAP2 and it says the following Reg online and hook state OFF.

I've got a Linksys PAP2 on my Vonage account with unlimited usage, but my softphone-addon account only has 500 minutes. Anyone ever try to setup their * to mimick the Linksys PAP2 ? Any comments or suggestions on what problems I might run into if I try? -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm having a real problem with one of my linksys pap2. On outgoing calls the callee will ring, but caller (pap2) will not here it ring When the callee answers, no audio is transmitted either way. Asterisk reports the call connected and bridged correctly. Now the kicker is that sometimes it works and other times it doesn't. I have had the most luck calling land lines, but sometime

Hi all, I have a problem with the dialing tone in PAP2: When making a call, I can hear the calling tone 5 times and then it stops. The called party still hears the call but not the calling party. I've playing around with different parameters on the PAP2 web config with no success until now. Anyone has seen the same probelm? Thanks, Jose