similar to: Weird problem in wctdm24xxp driver

i have a full fxo TDM24 and i have problem with installing it. when i run modprobe wctdm24xxp dmesg shows the following messages. and it waits for ever and nothing will happen. i'm sure that: - the power is plugged into tdm24 board - udev is configured and is working with other tdm cards. - zaptel.conf is configured. Zapata Telephony Interface Registered on major 196 Zaptel Version:

Hi, Before I report a bug on http://bugs.digium.com, I would like to know if someone is seeing the same error message. Personally I am not using wctdm24xxp but other modules such as wcte12xp and wctdm. The latter modules load fine and are compiled with pci_register_driver as expected. The only module that seems to require the deprecated function pci_module_init is wctdm24xxp. Is this normal?

I'm trying to configure a TDM808P card on debian. When I modprobe wctdm24xxp i get this error FATAL: Module wctdm24xxp not found. FATAL: Error running install command for wctdm24xxp I think i have successfully compiled the zaptel drivers, and the card appears when i do a lspci 02:06.0 Ethernet controller: Digium, Inc. Unknown device 0800 (rev 11) Subsystem: Digium, Inc. Unknown

Good morning, I have a digium wctdm24xxp in my asterisk box, i am not able to see the callerid when the call is incoming from the fxo line, i live in Brazil, how can i change the signaling from fsk to dtmf? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi guys, I'm building a server that need to host 2 digium TDM24 cards. I know any 3U server with 2 PCI-E slots would do. Since I do prefer supermicro server, but getting one configured is pretty darn hard. Any suggestions here? Cheers, Kelvin Chan | Positronics Ent. Product Development | | unit 272 604-628-9330 (direct) | 8128 128th St.

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

I am currently running Asterisk 1.2.8, on an AMD Sempron 3100+ (ASUS K8N Nforce based board). I am using a Digium wctdm24xxp to terminate 8 (2x quad) FXO lines. Using ztmonitor (From zapata) I cannot see that there is any registerable incoming volume from these lines. I've been running them at rxgain = 25 (zapata.conf) to make the audio audible, however this creates poor call quality issues

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

Hi, sorry for my insistence but this is a big problem for me..my steps for remove card are ok ? Thanks. ------ Salvatore. ----- Original Message ----- From: "Sasa" <sasa at shoponweb.it> To: <asterisk-users at lists.digium.com> Sent: Monday, November 26, 2007 4:25 PM Subject: [asterisk-users] Remove a TDM Card > Hi, I would like remove a Digium TDM2400P from

Hi. Please help. When trying to compile Zaptel 1.4.5.1 I get the following: /build/include/linux/modversions.h -DSTANDALONE_ZAPATA -I.. -o base.o -c base.c base.c:48:29: linux/workqueue.h: No such file or directory base.c:292: warning: `vpm150m_firmware' defined but not used make[2]: *** [base.o] Error 1 make[2]: Leaving directory `/usr/src/zaptel-1.4.5.1/wctdm24xxp' make[1]: ***

Hi All, This is a request for testing for users of Asterisk 1.4 or 1.6 with any of the following Digium VoiceBus based cards: TDM2400P, AEX2400, AEX800, TDM800P, TDM410, TE120P, TE121, and/or TE122. From a practical standpoint, this branch should allow these boards to work in more systems / configurations where IRQ misses caused problems in the past. The updated wctdm24xxp and wcte12xp

hi all, i have problem with dtmf detection on wctdm24xxp with full fxo and vpm module. after pushing dtmf tones on my phone for several times the card just detects one or two digits randomly.so now i can't use any voice menu on my box with this card. i have tried the following scenarios: - the card with / without vpm module has the same dtmf detection problem. - relaxdtmf=yes/no didn't

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

When I compile dahdi I see these warnings: WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/wctdm24xxp/wctdm24xxp.ko] undefined! WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/dahdi.ko] undefined! And "modinfo dahdi" shows that the driver was built for a 2.6.17 kernel, SMP mod_unload 586 4KSTACKS gcc-4.1 If I "modprobe -a dahdi", I get

Hello I purchased an AEX800 card to replace the ageing cheap channel bank/T1 card solution a few months ago, assuming that it would be a more robust solution for my small scale phone system. However, it appears to be anything but that. Originally implemented as a XEN dom-u virtual machine on a large server class machine, using PCI passthrough to pass the AEX800 and a small older TDM400, then

Hi All, Running asterisk 11.25.3, the /proc/cpuinfo says Intel(R) Xeon(R) CPU X5675 @ 3.07GHz lsmod | grep dahdi gives dahdi_transcode 16384 1 wctc4xxp dahdi_voicebus 61440 2 wctdm24xxp,wcte12xp dahdi 225280 11 wctdm24xxp,wcfxo,wctdm,dahdi_transcode,oct612x dahdi_voicebus,wcb4xxp,wct1xxp,wct4xxp,wcte11xp,wcte12xp crc_ccitt 16384 2

Have a new TE133 in a dell R320. dahdi_cfg -vvv shows: DAHDI Tools Version - 2.9.1 DAHDI Version: 2.9.1 Echo Canceller(s): Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 02: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 02) Channel 03: Clear

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools