similar to: directed call pickup with PICKUPMARK

Hi! What are the typical ways to work around the 64 groups limit? thanks klaus

Hi all, how can I pickup a call from a queue? Which context parameter do I have to specify? The context that calls the queues application is ext-queues. This is what I tried so long (777 is the extension of the queue I want to pickup from): exten => _**ZXX,1,Noop(Attempt to Pickup ${EXTEN:2} by ${CALLERID(num)}) exten => _**ZXX,n,Pickup(${EXTEN:2}@from-did-direct) exten =>

Hello list, I try to pick up a ringing extension but nothing works. To be clear, I'm trying to pick up extension 10. [Jun 14 17:37:34] -- Executing [**10 at from-TESTCORP:4] Pickup("SIP/testcorp3-00000041", "10 at 123456") in new stack [Jun 14 17:37:34] NOTICE[16555]: app_directed_pickup.c:159 pickup_exec: No target channel found for 10. [Jun 14 17:37:34] --

Hi, I'm banging my head over this. Usually, I'm using a SIP hardphone feature called "Call Pickup Starcode" to enhance BLF with Directed Call Pickup : basically, SIP hardphone (here a Thomson ST2030S) is configured to send an INVITE message whenever a BLF is pressed while blinking. The INVITE is build with the extension number (attached to the BLF that was blinking and pressed)

Hi! I'm using ael language and I need to pick up a call from outside to an internal number. for example: i'm 120 the phone 100 rings, it's a call from outside. now I pick up the call with: *8100 and I would expect to answer the call but the response is Declined the Puckup code is below: _*8X! => { Pickup(${EXTEN:2}); Hangup(); } the problem is if an another number ( 130) calls

Hi! > How to do this ?? > To proceed with your answer on PICKUPMARK, where do I put this ??? Look at the example for Asterisk 1.4 on this page: http://www.voip-info.org/wiki/view/Asterisk+cmd+Pickup Philipp

Hi! I have the following weird problem: phones A,B and C are in the same callgroup/pickupgroup. A call B, B is ringing, C calls *8. Now, B is CANCELed, C gets 200 OK, but A is still in Ringing. Is there anything else I have to configure? thanks Klaus

Hello, when picking up an incoming call from one ip phone on another ip phone, the call terminates after about 5 to 10 seconds. When reading out the hangup cause variable in the h-extention of the dialplan, the hangup cause seems to be 111. In the dialplan output, you can see that SIP-peer sipacc3 picks up the incoming channel SipAgenT01-00001454, and the call is answered. After 7 seconds,

I've tried the directed pickup like explained in http://www.voip-info.org/wiki-PBX+Call+Pickup but I've got no way doing it work. When I call the ringing phone it use the second line of that phone Group call pickup works perfectly. Is there some special configuration to do to make it works? Best regards, ?ric

Polycom Phones (updated for 3.2.X firmware with asterisk 1.6.1 Jan/2010) With SIP 3.2.X firmware (available on the Polycom download site) and Asterisk 1.6.1, Polycom phones now support a full featured BLF showing statuses of Ringing, Inuse and Online and one touch directed call pickup. On the asterisk side all that needs to be done is to add a hint to the extension and enable directed pickup.

Hi! I've went through the READMEs and could not answer this question: During installation, the Setup program asks: Would you like update/upgrade wanpipe drivers? (y/n) For a pure Asterisk TDM installation - is it required to patch the kernel or is this only when using the sangoma cards as WAN router? regards klaus

Hi, I've used various patches with asterisk 1.4 to have support for call pickup and notification with good results. Now I'm trying vanilla 1.6.2 with its official support for "dialog-info +xml" notifications with no success. This is what i'm doing: - Phone A has a key configured as type "extension" pointing to Phone B. - In sip.conf I added

Hi, Latest SIP firmware for Polycom 601 is 3.1.6. With this, is Directed Pickup supported ? At the moment, when an extension is ringing, I can see BLF turning to solid Red but I can't see it turning to Blinking Red. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello all Sorry for the repost, but I believe this is essential for Aastra phones to use directed pickup with BLF in 1.2 (and it's still experimental in 1.4 I think). pickup-mgernoth-2006-07-28.patch.txt If anyone knows otherwise than that this is still required in latest 1.2 or 1.4 please reply with success/failure stories. Any info would be appreciated. We can get directed BLF pickup

Hi! I am looking for a tool (application or webinterface) which shows me the current status of an Asterisk server, e.g.: - Status of the SIP peers (registered/offline) - current incoming and outgoing calls - start-time, numbers, some history - history (calls stopped in the last 15 minutes, who hang up?) - should be possible to link those calls to the relevant SIP peers -

What's the proper syntax for implementing directed call pickup? Running cvs-head from today (9/24/05 including Mark's fixes), and tried: exten => *99,1,Pickup(${EXTEN:3}) but that does not seem to work, and there isn't an example in the configs directory. 'show application pickup' suggests the above should work with our sip phones, but apparently I'm missing

Hi! I have the following problem with Asterisk 1.4.23: ATA w/ T.38 Asterisk ATA w/o T.38 --------INVITE--------> --------INVITE--------> <-------200OK---------- <-------200OK---------- --------ACK-----------> --------ACK-----------> --------INVITE

Hi! Is it somehow possible to evaluate the SIP response code inside the dialplan? I have an Asterisk server which forwards requests to various PSTN gateways with SIP. If the Dial() attempt is not successful I want to differ at least these 3 options: - called destination is busy (486): e.g. activate auto-redial - called destination does not exist, unassigned number (404) - gateway is broken,

Hi! All the AEL examples have a semicolon after the closing curly bracket, e.g: context test { 1 => Hangup(); }; but without ; it works fine too, e.g: context test { 1 => Hangup(); } So - what is the reason for the ; after the closing curly bracket? thanks klaus

I'm trying direct pickup feature but it doesn't work. Wiki says: "Directed pickup, this allows you to pickup a call at a specific extension, maybe you're in another office and you hear a phone ringing and wonder if it's yours. You dial the pickup number and your extension, and the call will only transfer if it is your extension." Instead group call pickup (*8) works.