similar to: TDM2400 and 3.3v pci

Does anyone know if a TDM2400 will fit into a Dell 2850? Kerry Garrison Director of Technical Services Tech Data Pros - Orange County's Mobile IT Service Provider (949) 502-7819 x200 - <mailto:kerryg@techdatapros.com> kerryg@techdatapros.com <http://www.techdatapros.com/> http://www.techdatapros.com -------------- next part -------------- An HTML attachment was scrubbed...

No I got confused....yes they are FXO modules with POTS lines coming from bell attached. The only thing I can think of is that since the card supports 3.3v or 5v PCI slots that maybe on a 3.3v slot it requires the other connection all the time because it really does need the 5v and is just not picky about where it comes from. -Jonathan -----Original Message----- From:

Hi, I'm trying to connect an HDL F10 device for a friend living in Brazil to the TDM2400 on his Asterisk server. That device should behave like a normal doorbell and it is if connected to an analog PBX. I connected to the TDM2400 and everything works fine except for one thing: when the called party hangs up his phone, the F10 HDL device does not hang up. I'm not brazilian and not

Hi List... I have an asterisk box with one TDM2400, it has 8 FXS's and 12 FXO's, and it also has the echo canceller... I'm running Asterisk 1.2.13 and Zaptel 1.2.12 with the Kernel 2.6.9-34.0.2.EL I'm using Polycom's 501 with the SIP 1.6.2.0041 The problem is when someone dials to or from the PSTN through the TDM2400, the voice quality is crappy...Instead of hearing:

We have a recently deployed server with a new TDM2400 card that will not put dialtone or audio on FXS ports after the physical server restarts (though they will ring if called, there's just no audio on the line if the phone at the other end picks up). The symptom can be resolved by stopping Asterisk, restarting DAHDI, and then restarting Asterisk. So far, this has happened on both times the

Good Day List, I'm having some issues with echo cancel on my Asterisk box, and have done extensive reading and have gained some useful pointers from this list but have a couple of hopefully fairly simple questions. The Asterisk box is connected via 20 FXO ports on a TDM2400 with the Hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a

Hi, I'm running FC3 with kernel 2.6.11. All the binary files and zaptel kernel modules is not available to system at boot time. They are extracted in a ram disk at system startup and then zaptel modules are loaded manually and so on. I have no problem with this boot routine and i've been tested all digium cards (expect tdm24) and they work fine till now. The problem appeared when i

Hi, >From a chat with Kevin Fleming during last Astricon Europe in Paris, I understood that Digium was about to support TDM bridging with TDM2400 board. This feature had to be introduced with 1.4 release. Is my understanding correct ? If correct, would it be reliable enough to bridge 14400b/s fax calls though I know, fax were not officially supported or shall I use Sangoma boards for that ?

Hello everybody, I would like to implement "callback" function. When I call a person and his extension is busy I can press, for example, 5 and get a callback when his phone is not busy anymore. When I create a call file and copy it to spool call folder asterisk makes a call. One problem is that when extension is still busy my phone rings and I get busy tone of the person who I am

Hello - I've been running Asterisk (quite happily!) for several years now using a Digium TDM400P card in an old Linux box (P4 1.6 w/ 256MB RAM). I'm also running another old PC running m0n0wall as a firewall. Between these two boxes, that run 24x7, I'm drawing a lot more power than needed and hoping to make a dent in my monthly electric bill by consolidating the two into a single box

http://www.mixdown.ca/~asterisk/ The card seems to be working fine. Don't expect warranty on it though. :-) Why? Because I wanted a quad-span T1 card which worked in the high-end systems I was intending it for, but that I could also keep a few in stock and if the system mainboard failed, pull the card an put it in a standard PC system. I didn't want to have to stock 3.3V and 5V

Hi, I just bought the E100P from digium. It has both keys: 3.3V and 5V, so it would fit both, in a 5V-PCI slot and in a 3.3V PCI slot. Is it true, that I can plug it without destroying it in an ordenary 5V PCI slot? Roger.

Hello list, I am encountering a bit of a problem in working with incoming calls with a TDM2400 and * 1.2.4; when a call comes in, * will correctly detect the ringing, but will sometimes report multiple "Attempting native bridge". What I do is basically that when a call comes in, I dial a different box through the same Zaptel interface and I get logs like this: [call comes in]

Hello, I've installed two Digium TDM2400 cards on my server. One has 24FXS and the other has 16 FXS and 4 FXO. They are both connected to power. Unfortunately some of the FXS module fail to initialize and I find following messages in the logs (the rest of the FXS modules work well). Could someone give me some advice? !!!!!!! LOOP_CLOSE_TRES iREG 1C = 1 should be 1000 Feb 9 18:09:45

Hello All I have a TDM2400 card with 4 FXO, and the the following problem: This card answered all the calls, but for the caller, the call is ringing and I don't hear nothing when it has picked up. Here is piece of my log: Thanks for any help. == Starting post polarity CID detection on channel 21 -- Starting simple switch on 'Zap/21-1' -- Executing [s at entrada:1]

Hello Fellows! I have a TDM2400 and I can't put it to work. Every time it receive a call the Asterisk handle it and call the SIP phone; when people pick up the fone they don't hear nothing and the caller hear the phone rings and nothing happens. In Asterisk console I can see the message answered by the SIP's phone. I lost a lot of time trying to solve this problem without success :(.

does * support call return? i want when the operator transfers a call if the transferee is busy or doesn't answer the call the call return back to operator again... this feature may be called: call return on busy call return on no answer Paradise Dove

Dec 1 12:08:43 WARNING[6189]: channel.c:495 ast_channel_walk_locked: Avoided deadlock for 'SIP/2502-6303', 10 retries! Dec 1 12:08:44 WARNING[6189]: channel.c:495 ast_channel_walk_locked: Avoided deadlock for 'SIP/2502-6303', 10 retries! Dec 1 12:08:44 WARNING[6189]: channel.c:495 ast_channel_walk_locked: Avoided deadlock for 'SIP/2502-6303', 10 retries! what does this

Hi all, Years ago, I was pretty sure attempting to use two TDM400p cards in one machine was recommended against by Digium ... probably because the cards couldn't hack it, and/or interrupt problems etc I have seen some posts recently that seem to indicate it is in fact possible these days thanks to some updated firmware perhaps? ..... I just need to have two in the server because the 4 ports

Does anyone know if there are any plans for Zapata or anyone else for that matter to come out with a 3.3v PCI version or PCI-X version of those cards? Gene