similar to: Digium S101I as a traveling companion

How to configure Digium S101i adapter to work with "pickupexten *8" ? I have few Sipura adapters and "*8" work OK but my new Digium S101i refuses to cooperate. -- #Joseph

Is there anyway to control echo on Digium S101I adapter? -- #Joseph

I have one Digium adapter S101I on a local network and I'm losing the connection periodically. I'm using Asterisk-1.2.21.1 There is no pattern, sometimes it stays connected for a weak sometimes longer. In comparison I have few Sipura adapters and they stay connected for months (never lost single connection). -- #Joseph

Does anybody know what DTMF coding does S101i adapter using? I've been testing one for over a week and here are my observations: - DTMF signaling is working perfectly with Asterisk, much better than Sipura 3K Though, I think the Asterisk "iaxy" firmware is buggy, the unit is using auto-update feature; so I have Asterisk 1.2.13 and iaxy firmware version is: 23 When enable in

When I try to call out to FWD over IAX2 I get: Call rejected by 65.39.205.121: Unable to negotiate codec I'm using asterisk-1.0.5 (the same settings works fine with *0.9) I've standard settings in iax.conf [general] bindport=4569 register => xxxxx:xxxxxx@iax2.fwdnet.net [iaxfwd] type=user context=fromiaxfwd auth=rsa inkeys=freeworlddialup disallow=all allow=ulaw -- #Joseph

That little Digium adapter S101I is a nice and compact (good for travel) but has a serious limitation, it doesn't support bridging. If I have four/five of these units registered to my asterisk server (over the Internet) and with standard DSL or Cable connection all for of them connected and in use (utilizing G711); my upload bandwidth will get saturated as all of them have to go via my

I'm testing Teliax tall free number line and I'm experiencing long delay about 1sec. during conversation. When I call myself over FWD the response is normal no delay or cut messages. When I call my number over FWD the is a long delay, welcome message usually cuts off few first words and during conversation my voice arrives after about 1sec. delay. Since, the 800-number is only accessible

I've setup my IAX2 over FWD and it is working I can receive a test call and I can call out. Though I cannot figure out how to dial 1-800 numbers over FWD When I dial 1-800 it hangs up on me. Here is a typical session: Called xxxxx:xxxxxxx@iax2.fwdnet.net/18007425877 -- Call accepted by 65.39.205.121 (format ULAW) -- Format for call is ULAW -- Hungup

Are there any adapters that would allow me to connect asterisk to wifi or we are not there yet? I have Digium adapter S101i that was discontinued but similar device that would connect to wifi network and a cell phone would be handy. -- Joseph

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

On Tue, Dec 23, 2014 at 6:34 PM, Rusty Newton <rnewton at digium.com> wrote: > On Tue, Dec 23, 2014 at 4:17 PM, Joseph <syscon780 at gmail.com> wrote: >> Are there any adapters that would allow me to connect asterisk to wifi or we >> are not there yet? >> I have Digium adapter S101i that was discontinued but similar device that >> would connect to wifi

I just changed the from DSL to Shaw Cable (static IP) configure the firewall but now asterisk I can not register with FWD nor VoipJet calls going out. I am using IAX with FWD Did I missed to change a setting? I don't think there is any though. I am on shaw extreme connection; I just talked shaw tech. and they are not blocking any port - I was told. So why IAX will not register with FWD and

I would like to implement enum lookup in my dial plan but searching for solution / implementation I'm getting confused what is current standard. On some pages I read that the ENUMLOOKUP is not in development anymore and suggesting on using Enumlookup.agi scrip , some are saying that Asterisk 1.2.0 comes with a new powerful ENUMLOOKUP. So there is probably no need to use this script anymore;

I've setup SPA-3000 and when the calls come through my phone is rining almost instantly but the [demo] doesn't answer till after about 13 seconds. So I have about 13 seconds delay and I don't know what setting is causing it; here is a part of my settings from extension.conf. [from_pstn] exten => 1000,1,Goto(demo,s,1) [demo] exten => s,1,Answer ; Answer the

Is anybody familiar with these IP phones AT-723 or AT-323 I think it is made by this company: http://www.atcom.com.cn/at723E.html -- #Joseph

After somebody records a message asterisk notifies me and encloses the WAV file. Though I'm not sure if this is a WAV format. I can not play it. According to the file specification it is: msg0000.WAV: RIFF (little-endian) data, WAVE audio, GSM 6.10, mono 8000 Hz How to play received message? -- #Joseph

Has anybody tried NVFaxDetect Fax detection for sip SIP/IAX channel? There is a new application from Newman Telecom for fax detection. http://www.sineapps.com/news.php?rssid=575 Current Asterisk Fax detection doesn't work for me as I don't have Digium cards; I'm using Siupra -- #Joseph

I'm just curious why Sipura isn't using free IAX protocol with their devices instead of SIP? With IAX NAT traversal would have been easier, so why are they using SIP. Is there any politics in it? -- #Joseph

When I use DISA I get congestion when I try to reach 1-800-number: Here is the context: [disa] exten => 087,1,Answer exten => 087,2,DigitTimeout,8 exten => 087,3,ResponseTimeout,20 exten => 087,4,Authenticate(985) exten => 087,5,DISA(951|disa-access) [disa-access] include => tollfree include => outgoing-voipjet [tollfree] ; ; terminate toll-free no.'s via fwdnet ; US

Can anybody share information how to install NVBackgroundDetect? I have the app_nv_backgrounddetect.c but I'm missing: app_nv_backgrounddetect.o and app_nv_backgrounddetect.so and have no idea how to generate them. Wiki point to contact Newman Telecom but all I received was the app_nv_backgrounddetect.c and no instruction how how to install it. The installation instruction from wiki